®
®
Shoreport
SHOREMASTER.COM
Parts List
DESCRIPTION
QTY
ITEM
4' x 10' Floating Poly Dock
2
1
ShorePort Front Connector
2
2
4' Poly Dock End Connector
1
3
Shoreport 1' Side Rear Connector
1
4
Shoreport
2
5
2' Notched Connector
1
6
Shoreport Rear Pipe Bracket with Hardware
2
7
The diagram below shows a typical ShorePort to poly dock installation. Before attaching ShorePorts to
dock make sure dock is anchored properly. Consult with your local dealer for anchoring requirements. If
needed you can attach ShorePorts rear pipe brackets to the back side of the ShorePorts. Remove the
bottom wear plate so the pile guide does not bind up on the pipe.
Note:
Refer to Poly Dock installation instructions for connector instructions.
3
6
1
2
5
7
4
ShorePort to Poly Dock
Failure to follow instructions may
result in personal injury and may
invalidate the applicable warranty.
Step 1.
Attach ShorePorts together
using 2' Notched Connector and
ShorePort 1' Side Rear Connector.
Step 2.
Attach ShorePort to Poly Dock
using ShorePort front connectors.
Step 3.
Slide 2" schedule 40 pipe into
pipe brackets and drive into ground
using post pounder.
DETAIL U
SCALE 1/35
U
ShorePort
Floating
Dock
Failure to follow instructions may result in personal injury and may invalidate the applicable warranty.
Note:
Refer to exploded parts drawing on following page for details on flexi hinge assembly.
Step 1.
Attach flexi hinge assembly extension plate to floating dock. Plates will have to be spaced about 116-1/4" between
plates so they will line up to corresponding plates on the ShorePort. Attach brackets to ShorePort and measure between to
verify spacing.
Step 2.
Assemble flexi hinge assembly. Slide connecting rod through hole in bottom of flexi hinge assembly weldment and
attach using oval screw (you will have to drill a pilot hole for screw). Next insert 5/16 x 4-1/2" hex bolt through lock washer,
rectangular washer and insert through hole in accessory top connector and thread into connector rod just enough to hold it
together. Attach rubber plate to flexi hinge assembly weldment using one flexi hinge assembly angle, three 3/8 x 2 hex bolts
and 3/8 nylock nuts. Attach two other flexi hinge assembly angles to other end of rubber plate using three 3/8 x 2 hex bolts and
3/8 nylock nuts (make sure to bolt through the holes not the slots).
Step 3.
Attach previously assembled portion of flexi hinge assembly to front of ShorePort so the connecting rod will end up
centered in the second vertical groove on the front of the ShorePort and attach the rear side flexi-hinge to the rear side of the
ShorePort so its connector rod is centered in second groove from the back of the ShorePort. Leave connecting rod bolt loose.
Step 4.
With no weight on the ShorePort float ShorePort next to floating dock and attach flexi hinge assembly extension plate
to flexi hinge assembly angles using four 3/8 x 1-1/4 hex bolts, flat washers and nylock nuts. Make sure ShorePort is floating
level in the water and rubber plate is level before attaching. After attached tighten all hardware. Torque 5/16" x 4-1/2" connector
rod bolts to 20 ft/lbs.
DO NOT OVERTIGHTEN AND DO NOT USE A HIGH SPEED DRILL.
Kit includes front and back
brackets to attach side of
ShorePort to floating dock.
ShorePort Side Mount Flexi-Hinge
Instructions
Part #: 1013365
Note
: If you are in an area with heavy boat traffic or
waves greater than 1'-6" use stand-off brackets
and pipe brackets instead of the flexi hinge
assembly. Side mount flexi-hinge assembly should
be used to attach only one ShorePort parallel to
dock. If multiple ShorePorts are to be attached side
by side pipe brackets should be used instead of
side mount flexi-hinge.
Side Mount Flexi-Hinge
