background image

 

 

 

 

INSTALL MOTOR ARM 

1. Run the 5/8” pivot bolt thru the pivot hole in the 
motor arm with threads away from dock.              
See Fig. 14. 

2.

 

Run the 5/8” bolt thru the pivot hole in the outer 

arm and lightly screw on 5/8” nut.  See Fig. 14. The 
motor arm should be in front of the outer arm.      
See Fig. 14.  

3. Rotate the motor up and over the pivot so motor’s 
rubber traction wheel rests on the boat lift wheel.              
See Fig. 14.  

4. The lift motor’s rubber traction wheel should be 
touching the lift wheel at roughly the 10 or 2 o’clock 
position. See Fig. 14. If the motor is not positioned 
correctly review 

Step 2:

 

Install Outer Arm Onto The 

Inner Arm 

on the previous page. Adjust the angle of 

the outer arm until the motor rests near the 10 or 2 
o’clock position on the lift wheel. See Figs. 12 & 13. 

5. Firmly tighten the band clamps on the winch post.  
using a 5/16” wrench. See Fig. 14. 

Note:  Lift up on the arms while tightening the 
band clamps.  This will allow you to firmly 
tighten the clamps. 

6. Tighten the 5/8” nut until it just touches the back 
side of the outer arm. See Figure 15.  

Note:  Do not over tighten the nut.  The wheels 
will not align if over tightening occurs. 

Note: Each boat lift will have a different sized 
space at the pivot point. Some lifts will have no 
space. See Fig. 15.  Even if there is some space 
between the motor arm and the outer arm where 
it pivots, the grooved rubber traction wheel 
should follow the boat lift wheel and not jump 
off. If you feel you need spacers, purchase large 
nylon washers at your local hardware store and 
place them between the arms and over the pivot 
bolt.  

6. Hook one end of the black rubber poly strap into 
the top hole of the motor plate towards the winch 
post. Fasten the other end to the open end of the 
inner or outer arm or directly onto the winch box. 
See Fig. 16. 
 

Note:  Black rubber poly strap fits most but not 
all applications. Alternates may be purchased at 
your local hardware store. 

 
 
 
 
 
 

 
 
 
 

 

 

     FIG. 14 

 

 

 

FIG. 15 

 

 

 

 

 

 

 

        
       FIG. 16 

Rubber 
Wheel  

Band 
Straps 

Motor 
Arm 

Pivot 
Bolt 

Motor 
Arm 

Space 
Between 
Arms 

Outer 
Arm 

5/8” 
Nut 

Motor 
Plate 

Rubber 
Poly 
Strap 

STEP 3: INSTALL MOTOR ARM ONTO OUTER ARM 

Pivot  
Bolt 

Содержание Lift Mate

















Отзывы: