background image

Desktop Quick-Start Guide • September 13, 2016

© Copyright 2016 ShopBot Tools, Inc.  

 page 14

Complete assembly by sliding removable front panel into 
place. 

Load Software

Minimum computer requirements:

Required: 

A PC running Windows XP, Vista (Home Premium / Business or higher), Windows 7, or high-

er.

Also recommended: 

The equivalent of a dual core (or higher) Pentium processor and a minimum of 

4GB RAM (8GB preferred).

The ShopBot Desktop requires one USB port for connection to the tool. Additional USB ports may be 
required for a mouse, keyboard, and other USB peripherals. An open USB port to transfer part files to 
the computer from a thumb drive is also helpful.

For schools: 

This software runs best with full administrative permissions enabled. It is 

strongly ad-

vised

 against setting up separate administrator and user accounts on the control computer.

For International customers: 

The computer used to run the machine MUST have the language set to 

“English (United States)” for the software to run correctly.

Computer Configuration

Important: 

To ensure trouble-free installation and operation, ShopBot recommends the following, prior 

to installation:

 

Install program using administrative account.

 

Set User Account Control (UAC, not applicable to Windows XP) to “Never Notify.”

 

Disable network connection.

 

Disable security and antivirus software.

 

Make sure the USB cable from the ShopBot is 

not

 plugged in.

Содержание D2418


































Отзывы: