3
16
1
5
6
4
2
3
15
15
14
7
10 11
12
20
21
9
8
15
13
5
5
19
18
15
17
22
23
23
Dolly Assembly Instructions
Tools required:
(2)
1
/
2
inch open end wrenches, (2)
7
/
16
inch open end wrenches, or
a socket set and a hammer.
1. Insert 2
1
/
2
inch long bolt through center hole in rear frame,
attach split lockwasher, nut and tighten securely.
2. Attach handle brace to back of rear frame with
5
/
8
inch long
machine screws, lockwashers, and nuts. (Finger tighten only.)
3. Position main frame inside rear frame. Attach (2)
5
/
8
inch long
machine screws, lockwashers and nuts in both sides. Tighten
securely.
4. Attach handle uprights, inside main frame (make sure buttons
at top face inward) using
5
/
8
inch long machine screws, lock-
washers and nuts. (Finger tighten only.) Align holes at top of
handle braces with holes in handle uprights. Attach with 1
1
/
4
inch long machine screws, lockwashers and nuts. (Tighten
securely.)
5. Go back and tighten machine screws at bottom of uprights and
braces.
6. Attach caster sockets (open end down) to front of main frame
using
5
/
8
inch long machine screws, lockwashers and nuts.
Insert casters into sockets.
ITEM
DESCRIPTION
PART NO.
1
Handle (14”)
20855-02
2
Handle upright
20856-01
3
Handle brace
20857-01
4
1
/
4
- 20 x 1
1
/
4
" Hex head machine
09074-99
screw (Black)
5
1
/
4
" External tooth lockwasher
23010-99
6
1
/
4
- 20 Hex nut (Black)
13035-99
7
Rear dolly frame (14”)
20832-00
8
Main dolly frame (14”)
20831-00
9
5
/
16
-18 x 2
1
/
2
" Hex head bolt
09073-99
10
5
/
16
" - Split lockwasher
02005-99
11
5
/
16
- 18 Hex nut
13003-99
12
Tank retainer bracket
20853-00
13
Threaded knob
23301-00
14
Axle (14”)
24406-00
15
1
/
4
- 20 x
5
/
8
" Hex head
machine screw
09028-99
16
1
/
4
- 20 Hex nut
13001-99
17
Caster socket
75400-01
18
Caster
67728-00
19
Bumper (14”)
87810-01
20
10” Wheel (25.4cm) Black
24205-00
21
Cap nut
43002-99
22
Accessory basket
74429-02
23
Basket Adapters
74429-50
Handle
Handle
Fig 1
Fig 2
7. Slide basket adapters onto handle.
8. See figure1 for correct installation of adapters.
9. Attach handle onto uprights by pushing down and holding buttons
in on uprights.
10. Place tank retaining bracket through slot and bolt in rear frame and
screw on knob.
11. Slide bumper down over main dolly frame until it bottoms out.
12. Place axle upright on a hard surface and hammer on (1) cap nut.
Place (1) wheel on axle and slide down to cap nut. Slide axle
through rear of frame and slide on other wheel. Before assembling
cap nut on other end of axle, be certain dolly is assembled
correctly. (You may place tank on dolly and tighten knob of
retaining bracket to be sureof correct assembly.)
13. After ensuring dolly is assembled correctly remove tank and place
dolly on side with installed cap nut on hard surface and hammer
second cap nut on axle.
14. Place accessory basket on adapters and pull out on outer rim of
basket and snap into place. Figure 2
