SAVE THESE INSTRUCTIONS
UNPACKING AND SET-UP
CHARGING BATTERY
1. Remove the tank cover by pushing in the side lugs with thumbs and lifting up on the tabs of the tank cover. Remove any accessories, which may have been shipped
in the tank.
2. Before replacing tank cover, refer to Dry Pick Up Operation or Wet Pick Up Operation in this manual to ensure you have the proper filters installed for your cleaning
operation.
3. Replace tank cover on the tank by aligning tabs with the lugs. Press down firmly on the upper housing until tank cover snaps into place.
4. Mount the wall bracket and tool holder following the instructions and illustrations in this manual.
5. Refer to the Operation section to select the power source needed for your cleaning operation. If using the battery, charge the unit following the instructions and illustrations under the
Charging Battery section of this manual.
6. Insert machine hose end into inlet of tank. Twist slightly to tighten the connection
(Figure A).
7. Attach one of the cleaning accessories (depending on your cleaning requirements) on the accessory end of the hose. Twist slightly to tighten the connection
(Figure A).
8. Your cleaner is ready for use.
I = ON, O = OFF
NOTE:
MANY MORE USEFUL TOOLS ARE AVAILABLE AT YOUR LOCAL DEALER OR SHOP-VAC
®
WEBSITE.
A
1. Choose a location to mount the wall bracket. To charge the vacuum while mounted to the wall, the location must be close enough to a wall outlet for the charger cord to reach when plugged
into vacuum. The location must be strong enough to hold the combined weight of the vacuum and the wall bracket. Do not place charger in an area of extreme heat or cold. Charger works
best at temperatures above 50° F (10° C) and below 100° F (38° C).
WARNING
– INADEQUATE MOUNTING COULD ALLOW THE UNIT TO FALL, CAUSING INJURY AND/OR DAMAGE TO THE UNIT.
2. Secure wall bracket to mounting surface with 2 screws provided or other suitable fastener. (
NOTE:
The screws provided are adequate ONLY for mounting into wood. Be sure to use the proper,
suitable fasteners for mounting vacuum to a surface other than wood.) Be sure wall bracket is level
(Figure 1).
3. Install vacuum by aligning groove on either side of tank to engage as the vacuum is lowered onto the wall bracket
(Figure 2).
4. To avoid possible injury or damage by dislodging vacuum from wall bracket or dropping tank during unlatching, always remove the entire vacuum from wall bracket and set on floor to empty
tank or service filter.
5. Before removing vacuum from wall bracket, check to make sure tank cover is secured to tank. To remove vacuum from wall bracket, grasp top handle with one hand and tank bottom with
other hand. Slide vacuum off of wall bracket by lifting straight up on vacuum
(Figure 3).
6. The tool holder can be mounted on the wall in close proximity to the wall bracket
(Figure 4).
Secure with mounting hardware provided.
INSTALLING WALL MOUNTING BRACKET
1
2
3
4
NOTE:
THE BATTERY PACK HAS BEEN SHIPPED IN A LOW CHARGE CONDITION. BATTERY REQUIRES AN INITIAL FULL CHARGE (12- 16 HOURS) PRIOR TO FIRST USE. OPTIMUM PERFORMANCE OF
UNIT WILL BE ACHIEVED AFTER BATTERY HAS BEEN CHARGED AND USED THREE TIMES. THE BATTERY ON THIS UNIT SHOULD NOT BE RUN COMPLETELY DOWN. IF THE LIGHT BLINKS RED, THE
BATTERY IS NOT TAKING THE CHARGE.
1. Make sure the power switch on top of the vacuum is in the off position.
2. With the rear of the vacuum facing you, locate the selector switch to the left of the charging port
(Figure 5).
Move the switch to the left position, if not already there.
3. Insert plug on charger into charging port on rear of vacuum
(Figure 6). NOTE:
Battery will only charge using the wall charger. It will not charge using the vehicle power cord
(not standard on
all models).
4. Plug charger into wall outlet. Light on charger will be red when unit is charging and change to green when it is fully charged. Do not turn the vacuum on while plugged into the charger.
5. Once vacuum is fully charged, unplug charger from wall outlet and back of vacuum.
6. If the unit does not charge while it is connected to the charger and the charger is plugged into an outlet, the battery charger or the battery in the unit may be bad. Battery must be recycled or
disposed of properly.
5
6
LIMITED TWO-YEAR WARRANTY
Shop-Vac warrants the vacuum cleaner for two years from the date of purchase to correct by repair or parts replacement without charge, any product defect due to faulty material or workmanship
provided that the vacuum cleaner is not used for rental service. This warranty does not cover accessories. Simply return the complete unit, (transportation prepaid), to the Authorized Shop-Vac
Service Centre nearest you (a complete list of Authorized Shop-Vac Service Centres is included with each vacuum cleaner). Shop-Vac assumes no responsibility for damage or faulty performance
caused by misuse or careless handling, or where repairs have been made or attempted by others. Proof of purchase date is required. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for
a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
