WARNING -
DO NOT LEAVE VACUUM UNATTENDED WHEN IT IS PLUGGED IN AND/OR OPERATING.
UNPLUG UNIT WHEN NOT IN USE.
SAVE THESE INSTRUCTIONS!
DOUBLE INSULATION
Do not operate if cord, plug or appliance is damaged. In your double insulated appliance, two systems of insulation are provided instead of
grounding. No grounding means is provided nor should a means for grounding be added to the appliance.
NOTE:
If power cord needs to be replaced, use only a Shop-Vac Service Agent.
EXTENSION CORDS
NOTE:
STATIC SHOCKS ARE COMMON IN DRY AREAS OR WHEN THE RELATIVE HUMIDITY OF THE AIR IS LOW. THIS IS ONLY TEMPORARY AND
DOES NOT AFFECT THE USE OF THE APPLIANCE. TO REDUCE THE FREQUENCY OF STATIC SHOCKS IN YOUR HOME, THE BEST REMEDY
IS TO ADD MOISTURE TO THE AIR WITH A CONSOLE OR INSTALLED HUMIDIFIER.
Use only a cord extension set that complies with AS3199. Conductor size must be 1.0mm
2
for length up to 25 metres and 1.5mm
2
for length
from 25 - 32 metres.
UNPACKING AND SET-UP
Remove tank cover and any accessories which may have been
shipped in the tank.
Before replacing tank cover, please refer to DRY PICK UP or WET
PICK UP OPERATION in this manual to ensure you have the proper
filters installed for your cleaning operation.
Replace tank cover.
Slip cleaner end of flexible hose into the intake port.
1.
2.
3.
4.
Attach the extension wands to the accessory end of the hose.
Twist slightly to tighten the connection.
Attach one of the cleaning accessories (depending on your
cleaning requirements) to the extension wand. Twist slightly to
tighten the connection.
Plug the cord into the wall outlet. Your cleaner is ready for use.
I = ON O = OFF
5.
6.
7.
LIMITED THREE-YEAR WARRANTY
Shop-Vac warrants the vacuum cleaner for three years from the date of purchase to correct by repair or parts replacement without charge, any
product defect due to faulty material or workmanship provided that the vacuum cleaner is not used for rental service. This warranty does not
cover accessories. Simply return the complete unit, with a copy of the receipt, to the place where you purchased your vacuum cleaner.
Shop-Vac assumes no responsibility for damage or faulty performance caused by misuse or careless handling, or where repairs have been
made or attempted by others. Proof of purchase date is required. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
B
B
B
B
A
A
B
B
B
CASTER ASSEMBLY
You will find four caster feet (a), four casters (b) and four screws
with your wet/dry vacuum. Assemble as follows:
1. With cord disconnected from receptacle and tank cover
removed, turn tank upside down so that the bottom is facing
up.
2. With tank inlet facing you, take caster feet marked with the
letter A
(Figure 1)
and place in slots on left front and right rear
of tank also marked with the letter A
(Figure 2)
and secure
with screws provided
(Figure 3)
.
3. Take caster feet marked with the letter B
(Figure 4)
and place
on right front and left rear of tank also marked with the
letter B
(Figure 5)
and secure with screws provided
(Figure 6)
.
4. Insert casters into feet by placing stem of caster into holes
provided and apply pressure until casters snap into place
(Figure 7)
.
5. Return tank to upright position.
a
b
1
2
3
4
5
6
7
A
A
A
A
A
A
