Handle
Handle
Tank
Basket
Basket
Adapter
Basket
Adapter
Pull Outward
on Basket
Handle
Handle
For 14" Diameter Tanks
For 16" Diameter Tanks
Handle
Handle
Tank
Basket
Basket
Adapter
Basket
Adapter
Pull Outward
on Basket
Handle
Handle
98
100
99
1
10
7
14
15
2
3
23
6
5
12
13
23
4
15
22
19
18
15
17
8
9
5
16
5
15
21
11
20
1. Handle
2. Handle
upright
3. Handle
brace
4. 1/4 - 20 x 1
1
/
4
" Hex head
machine screw (Black)
5. 1/4" External tooth
lockwasher
6. 1/4 - 20 Hex nut (Black)
7. Rear dolly frame
8. Main dolly frame
9. 5/16 - 18 x 2
1
/
2
" Hex head bolt
10. 5/16" Split lockwash
11. 5/16 - 18 Hex nut
ITEM NUMBER & DESCRIPTION
12. Tank retainer bracket
13. Threaded knob
14. Axle
15. 1/4 - 20 x 5/8" Hex head
machine screw
16. 1/4 - 20 Hex nut
17. Caster socket
18. Caster
19. Bumper
20. 10" Wheel (25.4cm)
21. Cap nut
22. Accessory basket
23. Basket adapter
BAND DOLLY ASSEMBLY
(Not standard with all models)
1. Place casters into sockets on band assembly.
2. Place tank upside down and slip band assembly over lip on bottom of tank.
3. Insert bolt and tighten nut until secure.
and slide down to cap nut. Slide axle through rear of frame and slide on other wheel.
Before assembling cap nut on other end of axle, be certain dolly is assembled correctly.
(You may place tank on dolly and tighten knob of retaining bracket to be sure of correct
assembly.)
13. After ensuring dolly is assembled correctly remove tank and place dolly on side with
installed cap nut on hard surface and hammer second cap nut on axle.
14. Place accessory basket on adapters and pull out on outer rim of basket and snap into
place
(Figure 100)
.
3
4
1
2
1. 55 Gal. band assembly
2. Caster
ITEM NUMBER & DESCRIPTION
3. Hex head bolt, 1/4 - 20 x 1
3
/
4
4. Hex nut, 1/4 - 20
FILTRATION
DRY PICK UP OPERATION
INSTALLING FOAM SLEEVE AND
REUSABLE DRY FILTER
(Not standard with all models)
WARNING
– ALWAYS DISCONNECT THE PLUG FROM THE
WALL OUTLET BEFORE REMOVING THE TANK COVER.
To pick up dust and dry material, you must install foam sleeve and reusable dry filter to ensure
proper filtration. If the vacuum has been used to pick up liquids, the foam sleeve must be
cleaned and dried before installing for dry pick up.
With tank cover in an upside down position, slide foam sleeve down over lid cage pulling until
foam sleeve completely covers lid cage
(Figure 101). NOTE:
Bottom of foam sleeve must be
positioned on the OUTSIDE of groove around lid cage for the reusable dry filter to fit properly
(Figure 102, 103).
Center the reusable dry filter on lid cage
(Figure 104),
slide mounting
ring down over filter until ring is positioned against the ribs of the lid cage
(Figure 105).
The
reusable dry filter should always be in position over the foam sleeve for dry pick up. To remove
the filter for cleaning, remove mounting ring and filter from lid cage
(Figure 106).
To clean the
reusable dry filter, shake off excess dirt and dust or (depending on the condition of the filter)
rinse with water. Allow the filter to dry completely and re-install.
DO NOT MACHINE WASH OR
DRY.
IMPORTANT: BEFORE INSTALLING REUSABLE FILTER BE SURE THAT FOAM SLEEVE IS
OUTSIDE OF GROOVE AND AROUND LID CAGE (Figure 102, 103).
NOTE: ENSURE THAT THE MOUNTING RING IS COMPLETELY SECURE AND IN POSI-
TION BY PRESSING DOWN FIRMLY AROUND THE RING IN SEVERAL PLACES. BE SURE
THE REUSABLE DRY DISC FILTER COMPLETELY COVERS THE FOAM SLEEVE. CHECK
TO ENSURE THAT ALL EDGES OF THE REUSABLE DRY FILTER ARE SECURE UNDER THE
MOUNTING RING.
CAUTION
– Keep Filters Clean
Keep Filters Clean
The efficiency of these vacuum cleaners is largely dependent on the filter.
A clogged filter can cause overheating and possibly damage the vacuum cleaner.
Clean or replace filters regularly. Do not use the vacuum or filters for collecting hazardous or
other health endangering materials.
NOTE:
Never machine wash or dry filters.
101
102
103
