background image

-4-

Model W1821 (For Machines Mfg. Since 3/10)

SA

FE

T

Y

10. NEVER LEAVE WHEN MACHINE IS RUNNING.

 Turn power 

OFF

 and allow all moving parts to come to 

a complete stop before leaving machine unattended.

11. DO NOT USE IN DANGEROUS ENVIRONMENTS. 

DO NOT use machinery in damp, wet locations, or 

where any flammable or noxious fumes may exist. 

12. KEEP WORK AREA CLEAN AND WELL LIT

. Clutter and dark shadows may cause accidents.

13. USE A GROUNDED EXTENSION CORD RATED FOR THE MACHINE AMPERAGE.

 Undersized cords over-

heat and lose power. Replace extension cords if they become damaged. DO NOT use extension cords 

for 220V machinery. 

14. ALWAYS DISCONNECT FROM POWER SOURCE BEFORE SERVICING MACHINERY

. Make sure switch is 

in OFF position before reconnecting.

15. MAINTAIN MACHINERY WITH CARE

. Keep blades sharp and clean for best and safest performance. 

Follow instructions for lubricating and changing accessories.

16. MAKE SURE GUARDS ARE IN PLACE AND WORK CORRECTLY BEFORE USING MACHINERY.

17. REMOVE  ADJUSTING  KEYS  AND  WRENCHES

.  Make  a  habit  of  checking  for  keys  and  adjusting 

wrenches before turning machinery 

ON

.

18. CHECK  FOR  DAMAGED  PARTS  BEFORE  USING  MACHINERY.

  Check  for  binding  and  alignment  of 

parts, broken parts, part mounting, loose bolts, and any other conditions that may affect machine 

operation. Repair or replace damaged parts.

19. USE RECOMMENDED ACCESSORIES

. Refer to the instruction manual for recommended accessories. 

The use of improper accessories may cause risk of injury.

20. DO NOT FORCE MACHINERY

. Work at the speed for which the machine or accessory was designed.

21. SECURE  WORKPIECE

.  Use  clamps  or  a  vise  to  hold  the  workpiece  when  practical.  A  secured 

workpiece protects your hands and frees both hands to operate the machine.

22. DO NOT OVERREACH

. Keep proper footing and balance at all times.

23. MANY MACHINES WILL EJECT THE WORKPIECE TOWARD THE OPERATOR

. Know and avoid condi-

tions that cause the workpiece to "kickback."

24. ALWAYS LOCK MOBILE BASES (IF USED) BEFORE OPERATING MACHINERY.

25.

 

BE  AWARE  THAT  CERTAIN  DUST  MAY  BE  HAZARDOUS 

to  the  respiratory  systems  of  people  and 

animals, especially fine dust. Make sure you know the hazards associated with the type of dust you 

will be exposed to and always wear a respirator approved for that type of dust. 

Содержание SHOP FOX W1821





























Отзывы: