Shop fox SHOP FOX W1740 Скачать руководство пользователя страница 29

Страница: 29 / 60

-27-

Model W1740 (For Machines Mfg. Since 1/13)

Conveyor.Tensioning

Figure.22.

Conveyor belt tension

adjustment.

The conveyor may slightly stretch with continued use and

will eventually need to be retensioned. If a loose convey-

or belt is ignored, it will slip and heat up the drive roller

damaging the roller, conveyor belt, and causing a wash-

board effect on the workpiece surface.

When you tension the conveyor, focus on tensioning the

adjustment bolts in equal increments. Tensioning one side

more than the other will cause tracking problems, which

will require you to take additional steps to get the sander

operating correctly.

To.tension.the.conveyor.belt,.do.these.steps:

1..

Use a magic marker, correction fluid, or fingernail

polish to mark the front of the conveyor tensioning

bolt on both sides (see

Figure.22

). This step will aid

you in keeping track of the rotations as you turn the

bolts, so they remain as equal as possible.

Note:

Removing the front right and left roller guard

covers makes it easier to access the adjustment

bolts. Be sure to re-install the guards when adjust-

ments are complete.

Turn both of the conveyor adjustment bolts counter-

clockwise one full turn at a time until the conveyor

belt no longer slips during operation.

— If the conveyor starts tracking to one side, imme-

diately turn the drum sander

OFF

and perform the

tracking instructions.

Tensioning Bolt

Содержание SHOP FOX W1740





























































Результаты поиска

Содержание SHOP FOX W1740

Отзывы:

Похожие инструкции для SHOP FOX W1740

Бренды по названию

Популярные бренды

Shop fox SHOP FOX W1740, Руководство пользователя

Результаты поиска

Содержание SHOP FOX W1740

Отзывы:

Похожие инструкции для SHOP FOX W1740

Бренды по названию

Популярные бренды