manualshive.com logo in svg

Shinko SGB, Инструкция по эксплуатации, Страница: 26 / 44

Поделиться
Скачать
Shinko SGB Скачать руководство пользователя страница 26

26

6.5

Instrument Setting Mode

Filter Time Constant

Sets the input filter time constant.
Input fluctuation due to noise can be decreased.

Setting Range

Indication

Factory Default

Multi-Display A Multi-Display B

0.0 to 10.0 seconds

Set value

0.0 sec

Sensor Correction

Sets sensor correction value.
Input value = Current input value + (Sensor correction value)

Setting Range

Indication

Factory Default

Multi-Display A Multi-Display B

-1000 to 1000 *

Set value

0

* The placement of the decimal point follows the selection.

Indication Time

Sets duration from no operation until Multi-Display A, Multi-Display B and each action
indicator are turned off.
When set to 00.00, they remain lit.
After indication time has elapsed, if any key is pressed while they are unlit, they will
light up again.

Setting Range

Indication

Factory Default

Multi-Display A Multi-Display B

0 : 00 to 60 : 00 (Minutes : Seconds)

0 : 00 .................... Continuous
0 : 01 to 60 : 00 .... Indication time

Set value

Continuous

Auto/Manual

If AUTO is selected, the value will be output corresponding to the input value.
When MANUAL is selected, the unit can enter Manual mode. The output value set in
Manual mode will be output.

Setting Range

Indication

Factory Default

Multi-Display A Multi-Display B

Auto

Manual

Manual

Содержание SGB













































Отзывы:

Нет отзывов