Shindaiwa EB262 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 40

background image

EB262

MAINTENANCE

X7501190802

29

© 09/19 ECHO Incorporated

Air Filter

Level 1.

1.

Close choke (COLD START
[

] position). This prevents

dirt from entering the carburetor
throat when the air filter is
removed. Brush accumulated
dirt from air cleaner area.

2.

Remove air filter cover. Brush
dirt from inside cover.

3.

Remove air filter and lightly brush debris from filter. Replace filter if it is
damaged, fuel soaked, very dirty, or the rubber sealing edges are
deformed. Clean the filter with a neutral detergent. Do not use solvents
for cleaning.

4.

If filter can be reused, be certain:

• The entire frame of the filter is securely seated in the housing.

• It is installed with the original side out.

5.

Install air filter cover.

Fuel Filter

Level 1.

Fuel is VERY flammable. Use extreme care when mixing, storing
or handling, or serious personal injury may result.

1.

Use a clean rag to remove
loose dirt from around fuel cap
and empty fuel tank.

2.

Pull the fuel filter from the tank.

3.

Do not remove the wire coil
clamp to remove the fuel filter.
Pinch the fuel filter with the
fingers on one hand and the
fuel line with the other hand.
Pull and twist slightly to
separate.

Parts Required:

Tune-Up Kit

Parts Required:

Tune-Up Kit

«
...
27
28
29
30
31
...
»

Содержание EB262









































Отзывы:

Нет отзывов

Похожие инструкции для EB262

Бренд: Votex Страницы: 61

Бренд: Echo Страницы: 6

Бренд: DOC Страницы: 12

Бренд: Pattfield Ergo Tools Страницы: 244

Бренд: Eagle power Страницы: 12

Бренд: Troy-Bilt Страницы: 11

Бренд: MTD Страницы: 28

Бренд: Weed Eater Страницы: 10

Бренд: Troy-Bilt Страницы: 52

Бренд: WORXNITRO Страницы: 144

Бренд: RCm Страницы: 107

Бренд: MEDO Страницы: 3

Sno-Thro 938000

Бренд: Ariens Страницы: 24

924 SNO-THRO 924108

Бренд: Ariens Страницы: 29

Бренд: Ariens Страницы: 16

Бренд: Ariens Страницы: 36

Бренд: Virnig Страницы: 19

Бренд: Tuchel Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды