Shindaiwa DGK150D Скачать руководство пользователя страница 31

Страница: 31 / 58

(2) Filling the Radiator

Remove the radiator cap.

Fill with coolant through the filler neck until
the radiator is full.

Re-attach and tighten the radiator cap.

< NOTE >



Use a 50:50 mix of Long Life Coolant (LLC) for engine coolant.

Use GM SPEC 6277M or equivalent.



Always use potable water when mixing the coolant.



Use same type of coolant with identical mixture ratio for the sub-tank.



Do not use a high LLC mixing rate unless absolutely necessary. Doing so could result in

overheating or malfunction.



Replace LLC every 1 year or 1,000 hours.



LLC is a toxic substance. Wear rubber gloves and other protective wear when handling.



If someone mistakenly ingests LLC, induce vomiting immediately and seek medical care.



If LLC gets on skin or clothing, wash with water immediately.



LLC is flammable. Store in a location where flame is prohibited and it cannot be accessed by

children.



Engine coolant could leak if the radiator is not completely tightened or there is a gap in the

seating face. Always be sure to securely tighten the radiator cap.



Do not add engine coolant past the FULL level line of the coolant sub-tank.

(3) Coolant Amount

(Unit : gal / liters)

Total Coolant Amount

6.3 (0.4) / 23.8 (1.5)

Value in parenthesis is the sub-tank capacity.

8-3. Checking the Fan Belt

●

Be sure to also read the separate Engine Instruction Manual.

(1) Fan Belt Tension

Tension should be optimum when the fan belt has 0.24 to 0.31
inch ( 6 to 8 mm ) slacks, when applying finger pressure
(about 100N { approximately 22lbf }) at midpoint between fan
pulley and alternator pulley.

Radiator Cap

Sub-tank

100N

Содержание DGK150D



























































Результаты поиска

Содержание DGK150D

Отзывы:

Похожие инструкции для DGK150D

Бренды по названию

Популярные бренды

Shindaiwa DGK150D, Руководство владельца и оператора

Результаты поиска

Содержание DGK150D

Отзывы:

Похожие инструкции для DGK150D

Бренды по названию

Популярные бренды