background image

20

Maintenance (continued)

WARNING!

Sharpen only the cutting 

teeth of a blade. DO NOT alter the 

contour of the blade in any way.

WARNING!

Wear protective gloves when handling or performing maintenance on 

the blade.

When the cutting edges of the blade become dull, they can be resharpened with a 

few strokes of a file.  In order to keep the blade in balance, all cutting edges must 

be sharpened equally.

Blade Sharpening

Round 

File

Multiple-tooth Circular Blade

Use a round file to maintain a radius of 0.04 to 1 to 1.5 mm (0.06”) at the base of 

each tooth. Cutting edges must be offset equally on each side.

Maintain a radius of 0.04 to 1 to 1.5 mm 

(0.06”) at the base of each tooth. Cutting 

edges must be offset equally on each side

Multiple-tooth Circular Blade

Carburetor Adjustment

Engine Break-In

New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be 

made. During the break-in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can 

be adjusted as required.

High Altitude Operation

This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to 

1,100 feet above sea level (ASL) (96.0 kPa). To maintain proper engine operation and emission compliance above 

1,100 feet ASL the carburetor may need to be adjusted by an authorized Shindaiwa service dealer.

IMPORTANT!

If the engine is adjusted for operation 

above

 1,100 feet ASL, the carburetor must be re-adjusted when operating the 

engine 

below

 1,100 feet ASL, otherwise severe

 engine damage may result.

NOTE:

Every unit is run at the factory and the carburetor is set in compliance with emission regulations. Carburetor adjustments, 

other than idle speed, must be performed by an authorized Shindaiwa dealer.

Adjusting Engine Idle

The engine must return to idle speed 

whenever the throttle lever is released. 

Idle speed is adjustable, and must be set 

low enough to permit the engine clutch 

to disengage the cutting attachment.

WARNING!

The cutting attachment 

must NEVER rotate at engine idle! 

If the idle speed cannot be adjusted 

by the procedure described here, 

return the trimmer to your Shin-

daiwa dealer for inspection.

Idle Speed Adjustment

1.  Place the unit on the ground, then 

start the engine, and then allow it to 

idle 2-3 minutes until warm.

2.  If the attachment rotates when the 

engine is at idle, reduce the idle 

speed by turning the idle adjustment 

screw counter-clockwise.

3.  If a tachometer is available,  adjust 

idle. Check Specifications page for 

correct idle speed

NOTE:

Carburetor fuel mixture adjustments 

are preset at factory and cannot be 

serviced in the field.

Idle adjustment 

screw

Содержание C282

































Отзывы: