Shindaiwa 81646, Руководство владельца/оператора

Страница: 15 / 48

15
15
26134
135-Hour Maintenace
Every 135 hours of operation,
remove and clean the muffler.
Forward
Muffler
Shield
Lower Muffler
Screw
Muffler
5 mm Muffler
Screws
Rear Muffler
Shield
Spark Ar-
rester Screen
Rear Muffler
Shield Screw
Long Term Storage
n
Remove the spark plug and pour
about 1/4 ounce of 2-cycle mixing oil
into the cylinder through the spark
plug hole. Slowly pull the recoil start-
er 2 or 3 times so oil will evenly coat
the interior of the engine. Reinstall
the spark plug.
n
Before storing the unit, repair or
replace any worn or damaged parts.
n
Remove the air cleaner element from
the carburetor and clean it thoroughly
with soap and water. Let dry and
reassemble the element.
n
Store the unit in a clean,
dust-free area.
Whenever the unit will not be used for 30
days or longer, use the following proce-
dures to prepare it for storage:
n
Clean external parts thoroughly.
n
Drain all the fuel from the fuel tank.
IMPORTANT!
All stored fuels should be stabilized
with a fuel stabilizer such as STA-BIL™,
if oil with fuel stabilizer is not used.
1. Prime the primer bulb until no more
fuel is passing through.
. Start and run the engine until it
stops running.
3. Repeat steps 1 and until the engine
will no longer start.
Blade Sharpening
When the cutting edges of the blade be-
come dull, they can be resharpened with a
few strokes of a file.
In order to keep the blade in balance, all
cutting edges must be
sharpened equally.
Shindaiwa Tornado® Blade
To sharpen the cutters on a Shindaiwa
Tornado Blade, use a 7/3-inch round
file. File the leading edge of each tooth to
a razor edge. The top plate of each tooth
should angle back 30°.
WARNING!
Sharpen only the cutting
teeth of a blade. DO NOT
alter the contour of the blade in
any way.
Multiple-tooth Circular Blade
Use a round file to maintain a radius of
0.04 to 0.06" (1 to 1.5 mm) at the base of
each tooth. Cutting edges must be offset
equally on each side.
Round
File
30°
Round
File
Figure 34
Figure 33
n
Remove the remaining fuel from
the fuel lines and carburetor.
Muffler Gasket
CAUTION!
Gasoline stored in the carburetor
for extended periods can cause hard
starting and could also lead
to increased service and mainte-
nance.
WARNING!
Never operate the
machine with a damaged
or missing muffler or spark arrester!
Operating with missing or dam-
aged exhaust components is a fire
hazard and could also damage your
hearing.
1. Remove the spark plug boot.
. Remove the two 4 mm engine cover
screws (located at the top of the recoil
housing).
3. Loosen the 5 mm engine top cover
screw (the screw is captive) and lift the
cover from the engine.
4. Remove the two 5 mm muffler screws.
Remove the lower muffler screw, then
lift the muffler assembly from the
engine.
5. Remove the rear muffler shield socket
head screw and, while noting the
orientation of parts, separate the
muffler shield. See Figure 3.
6. Remove the spark arrester screen and
clean with a stiff bristle brush.
7. Gently tap the muffler on a wood
surface to dislodge any loose carbon.
8. Inspect the cylinder exhaust port for
carbon buildup.
IMPORTANT!
If you note excessive carbon buildup,
consult with an authorized servicing dealer.
9. Reassemble the muffler in the reverse
order of disassembly.
Figure 32