background image

32

491s

*  Technical data subject to change without notice.

TECHNICAL DATA

MODEL

491s

Dimension

L × W × H

mm

395 × 250 × 290

Mass

Power head, dry

kg

4.8 Without chain and guide bar

Engine

Type

Air-cooled two-stroke single cylinder

Displacement

mL (cm³)

50.2

Carburetor

Diaphragm type

Magneto

Flywheel magneto: CDI system

Spark plug

NGK BPMR8Y

Starter

Recoil starter

Power transmission

Automatic centrifugal clutch

Fuel

Mixture ratio

50 : 1 ratio with 

shindaiwa

 Red Armor™, ISO-L- 

EGD (ISO/CD 13738) and JASO M345-FD two-
stroke, air-cooled engine oil.

Gasoline

Use 89 octane unleaded.  
Do not use fuel containing methyl alcohol, more than 
10 % ethyl alcohol or 15 %  MTBE.  
Do not use alternative fuels such as E-15 or E-85.

Tank capacity

L

0.490

Oil

Bar and chain

shindaiwa

 bar and chain oil

Tank capacity

L

0.280

Guide bar and 
saw chain

See page 23 for Chain and Guide Bar Combination

Lubrication

Adjustable automatic oil pump

Engine speed

Idle

r/min

2600 - 3600

Clutch engagement

3600 - 4200

Wide open throttle

11000 - 12500

Standard 
features

Front hand guard, Rear hand guard,  
Anti-vibration device, Spiked bumper,  
Throttle control lockout, Chain brake, Chain catcher, 
Spark arrestor muffler, Kick guard 

Содержание 491s





































Отзывы: