Shin-Nippon SLM-5000 Скачать руководство пользователя страница 32

Страница: 32 / 34

RB-473-B02M

8. Error Messages

8.1. Descriptions

Message

Status

Description

Measure Error

When the power is turned, values are not initialized
(values are not zero (0)).

Paper Empty

No papers are set in the printer.

Printer Cover Open

The printer cover is open.

Printer Heat Over

The printer is overheated.

EEPROM Fault

Abnormality of memory

Sensor Error

Abnormality of camera sensor

Error * * * (100

–

141)

Abnormality

of the

instrument

Abnormality of electronic parts (on the 'Control circuit board'

)

SPH Over

SPH value exceeds the measurement range.

CYL Over

CYL value exceeds the measurement range.

Prism Over

Prism value exceeds the measurement range.

ADD Over

Measurement

abnormality

ADD value exceeds the measurement range.

Retry Error

Measurement fails because of dust, flaws, unnecessary light,
and so on.

Notarget Error

Abnormality

of image

processing

The measurement light does not enter into the receiving light
sensor.



Display with a three-digit code (number).

8.2. Measures taken for the errors



Measure Error

The message appears if the lens is on the lens stand when the power is turned on, or if the lens under

the lens stand is dirty.

Remove the lens if it is on the lens stand. If the lens under the lens stand is dirty, gently wipe it with a

soft cloth. Then, turn the power back again. (See 6.1 Check before Measurement.)



Paper Empty

The message appears if no papers are set or papers are not set appropriately in the printer.

Set the paper appropriately. (5.4.3. Setting and replacement of printer paper.



Printer Cover Open

The message appears when the printer cover is open. Check the cover and close it if it is open.



SPH/CYL/Prism/ADD Over

The message appears when the lens exceeds the upper limit of the measurement range is measured.

Measure the lens within the measurement range. (See 9. Specifications.)



Retry Error

Notarget Error

The message appears when the direct sunlight or strong glare is on the instrument, or the lens under

the lens stand is extremely dirty or has some flaws.

When the lens under the lens stand is dirty, gently wipe it with a soft cloth. Then, turn the power back

on.

When error messages other than described above appears, or the situation

does not improve after the measures above are taken, cut the power and

unplug the power cord, and then contact your distributor.



Содержание SLM-5000



































Результаты поиска

Содержание SLM-5000

Отзывы:

Бренды по названию

Популярные бренды

Shin-Nippon SLM-5000, Руководство по эксплуатации

Результаты поиска

Содержание SLM-5000

Отзывы:

Бренды по названию

Популярные бренды