The temperature unit at the time of a sensor input is set up from
(℃) , (
℉
).
Not displayed when the linear input is chosen.
Scaling lower limit value at the time of linear input is set up.
Initial value :
Setting range :
、
Initial value : 0.0
Setting range : -1999
〜
9989 digits
Initial value : 100.0
Setting range : -1989
〜
9999
digits
Initial value: multi , voltage , current
Setting range: Chosen from 5-5.measuring range code table.
Combination of input type and measuring range is set by code.
6
Initial value : 0
S etting range :
−
500
〜
500 Digits
Initial value : 0.00
Setting range : ±5.00%
Initial value : 0
Setting range : 0
〜
9999 seconds
Used for correction of input errors such as sensor.
If offset correction is performed, control is also performed with the
corrected value.
Maximum input value is corrected within limit of ±5.00% of
measuring range.
If corrected, inclination of spang changes in straight line which
connects zero point and correction maximum value.
When input change is violent or noise is overlapped, used in order to
ease the influences.
In 0 second setting, filter does not function.
If key is pressed, it shifts to the first setting screen PV offset
correction screen.
Mode 2 lead screen
Output 1 PID1 proportional-band (P) setting screen
Output 1 PID1 Integral time (I) setting screen
PV offset correction (PV bias) setting screen
PV gain correction setting screen
PV filter setting screen
Mesuring range setting screen
Temperature unit setting screen
Input scaling lower limit value setting screen
Input scaling upper limit value setting screen
Input scaling Decimal point position Setting screen
Return to mode 2 lead screen.
(
4
)
Mode 2 screens Scale and PV setting
Mode 3 lead screen
key
key
key
key
Initial value : 3.0%
Setting range : OFF, 0.1
〜
999.9%
When performing auto tuning, no necessity for a setting basically.
If OFF is chosen, it becomes ON-OFF (two positions) operation.
Initial value : 120 seconds
Setting range : 0FF, 1
〜
6000 seconds
Output 1 PID1 Derivative time (D) setting screen
Initial value : 30 second
Setting range : 0FF, 1
〜
3600 seconds
When performing auto tuning, no necessity for a setting basically.
This screen is not displayed at the time of ON-OFF operation.
Becomes P operation or PD operation in I=OFF setting.
When performing auto tuning, no necessity for a setting basically.
This screen is not displayed at the time of ON-OFF operation.
Becomes P operation or PI operation in D=OFF setting.
The offset correction at the time of I = OFF ( P operation,PD operation])
is performed.
This screen is not displayed at the time of ON-OFF operation.
The differential gap at the time of ON-OFF operation is set.
Displayed at the time of P=OFF ( ON-OFF operation) setup.
Output1 PID1 manual reset setting screen
Initial value : 0.0
Setting range :
−
50.0
〜
50.0%
Output 1 PID1 differential-gap setting screen
Initial value : 5
Setting range : 1
〜
999 unit
Output lower limit value of output 1 PID1 is set up.
Output1 PID1 minimum limiter setting screen
Initial value : 0.0
Setting range : 0.0
〜
99.9%
Upper limit value of output 1 PID1 is set .
Output 1 PID1 maximum limiter setting screen
Initial value : 100.0
Setting range : output limiter lower limiter 0.1
〜
100.0%
Content is the same with output 1 PID1.
Output 1 PID2 proportional band (P) setting screen
Initial value : 3.0%
Setting range : OFF, 0.1
〜
999.9%
Contents is the same with output 1 PID1.
Output 1 PID2 integral-time (I) setting screen
Initial value : 120 seconds
Setting range : 0FF, 1
〜
6000 seconds
Contents is the same with output 1 PID1.
Output 1 PID2 derivative-time (D) setting screen
Initial value : 30 seconds
Setting range : 0FF, 1
〜
3600 seconds
Contents is the same with output 1 PID1.
Output 1 PID2 manual reset setting screen
Initial value : 0.0
Setting range :
−
50.0
〜
50.0%
Scaling upper limit value at the time of linear input is set up.
No setup
If key is pressed, it shift to the first setting screen, output 1
proportional band
setting screen. In this screens, PID which can be used in output 1, 1
〜
3
related Items and soft start of output 1,and proportional period output
characteristics are set up.
Initial value : the first place after decimal point (0.0)
Setting range : no decimal point 0
〜
the third place after decimal point
(0.000)
Decimal point position of input scaling is set .
Suppose that the difference between a lower limit value and
upper limit value is 10 or less,or over 10,000. In this setting,
upper limit value is compulsorily changed into that of +10 or ±
10000 digits. Upper limit value cannot be set as lower limit
value of +10 digits or less,or that of over 10,000 digits.
The screen of input scaling serves as a monitor at the time of a
sensor input.
Setting change cannot be performed.
NOTE
：
At the time of STBY (RST) and scale over output, limiter
value is disregarded.
NOTE
：
NOTE
：
(
5
)
Mode 3 screen Out 1 setting
key
key
key
key
key
key
key
key
key
key
key
key
key
key
key
key
key
Press
key in mode1 lead screen, or press
key in mode3 lead screen,
then being displayed.
