background image

6

Label

 

Some of the important information contained in this 
user's manual is also indicated on the battery charger 
label.

FCC compliance information

This device complies with Part 15 of the FCC Rules. 
Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and  
(2)  This device must accept any interference received, 

including interference that may cause undesired 
operation.

NOTE: This equipment has been tested and found to 
comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against 
harmful  interference in a residential installation. This 
equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful 
interference to radio communications. However, there 
is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause 
harmful interference to radio or television reception, 
which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:

 

- Reorient or relocate the receiving antenna.

 

- Increase the separation between the equipment and 

receiver.

 

- Connect the equipment into an outlet on a circuit 

different from that to which the receiver is 
connected.

 

- Consult the dealer or an experienced radio/TV 

technician for help.

Содержание STEPS E7000 SERIES

























































Отзывы: