manualshive.com logo in svg

Shimadzu UD 150L-30 EX, Руководство по установке

Поделиться
Скачать
Shimadzu UD 150L-30 EX Скачать руководство пользователя страница 15

 
3.2.2 Power ON check up 
 

• 

Check all DC and AC power according to the table below. 
 

Name Measuring 

point 

Voltage  Note 

T2 transformer 

10LA-0LA 

10.5V + 1V 

 

 100LB-0LB 

105V 

+ 

 10V 

 

T1 transformer 

L100-L0 

AC 105V + 5V 

 

 

L125-L0 

AC 130V + 10V 

 

 

A125-A0 

AC 125V + 5V 

Without Load 

 

A200-A0 

AC 200V + 15V 

 

 

135C-0C 

AC 142V + 10V 

 

 

20T-0T 

AC 21V + 2V 

 

DC power supply  J73/J74   4-7 

DC +5V + 50mV 

PS1 

 

J73/J74   2-5 

DC +15V + 400mV 

PS1 

 

J73/J74   6-5 

DC -15V + 400mV 

PS1 

 

J75          1-4 

DC +24V + 600mV 

PS2 

 

• 

Make sure MG-RS is activated. If not, turn power off immediately, and manually push the button on 
MG-RS to see if that was a mechanical jam. Also, check the cable connection on it. Fire accident could 
happen if this is not working. 

• 

Check to see if the charging voltage on VC+ and VC- (ANALOG-LF30 CP72 and CP73) is within 
range. (+10%) (3 

φ

 400 V input power to generator will results the charging voltage on VC+ and VC- 

approximately to be 560V) If not, you need to check the power line and XAT-2 again. 

• 

Perform IGBT Gate check as the following and make necessary adjustments before conducting X-ray. 
(Please check this part after you finish initial settings) 

 

Procedures: 
 

1)  Power off generator and wait about 5-10 seconds. 
2)  Measure VC+ and VC- with DVM to insure the charging voltage were all discharged. 
3)  Disconnect J202 and J203 on ANALOG-LF30 PCB to disable MG-L and MG-RS. 
4)  Add jumper between CP42 CVP1 and GND test point on ANALOG-LF30 PCB. Add another 

jumper between the cathode side of D27 and CP58 +15V. (Connection Diagram ANALOG-
LF30 9/27) Add another jumper between CP52 CHECK1 and CP56 CHECK2 on ANALOG-
LF30 PCB. 

5)  Connect oscilloscope channel one to CP1 E and CP2 G on GATE DRIVER-99 PCB mounted 

on IGBT-QA.(Probe signal on CP2, ground on CP1) 

6)  Connect scope channel two the same as channel one on IGBT-QC. (Float ground on channel 

two probe to prevent ground loop) 

7)  Set amplitude 5V and time 5 

µ

 sec. per division for both channels on the scope. Place the 

ground for both channels at the center of screen as well. 

8)  Turn on power of generator and select General Radiographic Mode. Then set 100 kV, 100 

mA, and 2.5 sec. 

9)  Make an exposure and wait about 0.1 to 1 second until the X-ray operation reach to its steady 

state.  

10)  Observe the waveforms and make the following adjustments if necessary.  
11)  Adjust VR12 PULSE ADJ on ANALOG-LF30 PCB so that the pulse width is 10.0 + 0.5 

µ

 

sec. at 5 V level. Also, check the phase difference is 11.1 + 0.5 

µ

 sec. at 0 V level. The 

positive peak voltage is less than 20 V and flat level is at 15 V or a little higher. The negative 
flat level is about –6 V. Repeat step 9) and 11) several times for the best results you can 
achieve. (Compare the waveform with the attached waveform.)  

UD150L30-FX/EX Installation Guide, REV_B          Page 15 of 35 

Содержание UD 150L-30 EX




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды