manualshive.com logo in svg

Shimadzu TOC-V CPH, Руководство пользователя

Поделиться
Скачать
Shimadzu TOC-V CPH Скачать руководство пользователя страница 4

TOCV-CP_IMshort_Control-ver-2_Rev07F 

 

Page 4 of 22 

(Software version ≥ 2.00) 

 

effective date: September 2007 

User 

Name of current user is automatically entered, if entered it cannot 
be edited 

Date of Creation 

Current date is automatically entered and cannot be edited  

Comment 

Enter additional system information (optional) 

 

Instrument Setup Wizard-2 :  Instrument Options 

Parameter 

Action / Description 

Oxidation 

Select “Combustion” 

Options 

Select the installed instrument components (TOC, ASI, SSM, 
Sparge Kit and 8-port Sampler) 
[The selected options determine which Instrument Setup Wizard 
screens will subsequently be displayed.] 

 

Instrument Setup Wizard-3 :  Instrument Parameters 

Parameter 

Action / Description 

Catalyst type 

Select the catalyst type (Regular, High Sense or TC/TN) 

Tubing Diameter 
Regular 
Suspended Particle 

Select the diameter size of the sample injection tubing. 
0.5 mm diameter 
0.8 mm diameter 

Cell length 

Select the cell of the NDIR detection 
(Long as default, short for SSM measurements) 

TC Furnace 

This item sets the TC furnace temperature 

Buzzer 

If this item is selected, a buzzer will sound with the press of each 
instrument key 

Auto regeneration of 
IC solution 

If this item is selected, IC reagent will automatically be generated in 
special situations (Please refer to the User Manual) 

Enable ready status 
check 

Select this option to enable the Ready Status Check function 
[recommended, thus software always verifies Ready Status of 
instrument  prior to starting measurement]  

TN Power 

If this item is selected, the power to the optional TNM-1 is turned 
on. 

 

Instrument Setup Wizard-4 :  ASI parameters 

Parameter 

Action / Description 

Tray Type 

Select ASI tray type (24 ml, 40 ml or 125 ml vial) 

Needle Type 

Select the needle type. (only active if Sparge Kit was selected) 
 

No of Needle Washes 

Select the number of times (0-10) the outside of the needle to be 
washed with dilution water, after each sample analysis 

No of Flow Line 
Washes 

Select the number of times (0-10) the flow lines to be washed with 
dilution water from the needle to the injection tube, at the 
completion of the sample sequence 

Rinse 

Select this option to rinse the sampling needle with dilution water 
between each sample. 

Rinse after acid 
addition 

Select this option to rinse the sampling needle after each acid 
addition. 

Stirrer on 

Select this option to use the magnetic stirrer. (if installed) 

 

Содержание TOC-V CPH























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды