background image

 

3. The device is equipped with a power cord and a plug. Before connecting, make sure the power switch (3) is in the OFF position (off).

Fig. 1. Scheme of connecting devices 

7. FUNCTIONAL DESCRIPTION switches and DIAL 

Ready for operation, the device attached to the connector (3). The inclusion of devices is confirmed by lighting of the LED (2). 

Ready for operation, the device attached to the connector (3). The inclusion of devices is confirmed by lighting of the LED (2). 

For storage or transport devices in freezing temperatures before the start of work to bring the device to an appropriate temperature 
!!!

Setting the welding current is made knob (4). Recommended values ​​of the welding current depending on the diameter of the electrode for the example 
the most commonly used electrodes in the table below. The switch (8) allows you to enable / disable function VRD. Enabling this feature will be 
confirmed by lighting of the LED (9). VRD function reduces the rated voltage of no-load condition of 70V to 20V for reasons of safety, however, hinders 
the starting performance. Selecting the operating mode to the user. Attention! For safety reasons, it is recommended to use the device enabled VRD.

OVERHEAT

AND

POWER

thirty 

200

60

90

120

150

180

2

3

6

7

VRD

8

4

9

1. Signaling device overheating 
2. The LED power 
3. The main switch 
4. The current control knob 
5. Nest "-" 

6. Slot "+" 
7. Display 
8. Switch VRD / standard 
9. LED function VRD 

Fig. 2. View of the front panel 

Содержание MMA 200












Отзывы: