ShenZhen Yuejiang Technology Dobot Magician Скачать руководство пользователя страница 119

Страница: 119 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

114

The printing window is displayed and the current printing temperature is shown

on the top corner of the window, as shown in Figure 5.137.

Figure 5.137 Printing window

Set

Temperature

200

and press down

Enter

to heat the extruder.

The temperature of the extruder should be above 170℃. Dobot Maigicain will

not start 3D printing until the filament is in the melting state. So you need to

heat the extruder first.

DANGER

The heating rod will produce high temperature up to 250℃, please be careful. Do not let

children play with it alone. The process needs to be monitored when it is running. After

the process is completed, please turn off the equipment promptly.

Before printing, you need to test the extruder to check whether the melted filament

flows from the nozzle of the extruder.

Click the feedstock extruder or click the given stepper, such as

0.1

(

recommended) on the

Operational

page and feed up to 10mm-30mm, as shown in

Figure 5.138.

Содержание Dobot Magician


























































































































































Результаты поиска

Содержание Dobot Magician

Отзывы:

Похожие инструкции для Dobot Magician

Бренды по названию

Популярные бренды

ShenZhen Yuejiang Technology Dobot Magician, Руководство пользователя

Результаты поиска

Содержание Dobot Magician

Отзывы:

Похожие инструкции для Dobot Magician

Бренды по названию

Популярные бренды