background image

 1

Overview 

      This Operating Manual covers information on safety 
and cautions. Please read the relevant information 
carefully and observe all the Warnings and Notes strictly. 

Warning 

To avoid electric shock or personal injury, read the 

Safety Information” and rules for safe operation carefully 

before using the Meter. 

Digital Multimeter Model KJ2815B/KJ2817B (hereafter referred 
to as “the Meter”) are 3 3/4 digits with steady operations, 
fashionable structure and highly reliable 

hand-held 

measuring 

instrument. The Meter uses large scale of integrated circuit with 
high performance A/D converter as its core and has full range 
overload protection. 
The Meter can measure AC/DC Voltage, AC/DC Current, 
Resistance, 

Capacitance,

 Diodes, Continuity, Frequency 

(KJ2817B only) , Duty cycle (KJ2817B only), Temperature 
(KJ2817B only) and so on. Backlight function also provided for 
both two model, it is convenient for operating in dark environment. 
They are both ideal tool for users. 

 

Unpacking Inspection 

       
Open the package case and take out the Meter. Check the 
following items carefully to see any missing or damaged part: 

z

 Operating Manual     1 piece 

z

 Test Lead                        1 pair 

Содержание KJ2815B



































Отзывы: