manualshive.com logo in svg

Shearwater DiveCAN Petrel 1, Руководство по эксплуатации, Страница: 70 / 70

Поделиться
Скачать
Shearwater DiveCAN Petrel 1 Скачать руководство пользователя страница 70

DocRevB

70

Shearwater DiveCAN

®

 Petrel

FCC Warning

a) USA-Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to Part 15 of FCC Rules� These limits are designed to provide reasonable 

protection against harmful interference in a residential installation� This equipment generates, 

uses, and can radiate radio frequency energy� If not installed and used in accordance with the 

instructions, it may cause harmful interference to radio communications� However, there is no 

guarantee that interference will not occur in a particular installation�

If this equipment does cause harmful interference to radio or television reception, which can be 

determined by tuning the equipment off and on, the user is encouraged to try and correct the 

interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna

•  Increase the distance between the equipment and the receiver�

•  Connect the equipment to outlet on a circuit different from that to which the receiver is 

connected�

•  Consult the dealer or an experienced radio/TV technician for help�

Any changes or modifications not expressly approved by the party responsible for compliance 

could void the user’s authority to operate the equipment�

Caution: Exposure to Radio Frequency Radiation�

This device must not be co-located or operating in conjunction with any other antenna or 

transmitter�

Contains TX FCC ID: T7VEBMU

Industry Canada Warning

b) Canada - Industry Canada (IC)

This device complies with RSS 210 of Industry Canada�

Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired 

operation of this device�

L‘utilisation de ce dispositif est autorisée seulement aux conditions suivantes :

(1) il ne doit pas produire d’interference, et

(2) l’utilisateur du dispositif doit étre prêt à accepter toute interference radioélectrique reçu, 

même si celle-ci est susceptible de compromettre le fonctionnement du dispositif�

Caution: Exposure to Radio Frequency Radiation�

The installer of this radio equipment must ensure that the antenna is located or pointed such 

that it does not emit RF field in excess of Health Canada limits for the general population; 

consult Safety Code 6, obtainable from Health Canada’s website

 www�hc-sc�gc�ca/ewh-semt/

pubs/radiation/radio_guide-lignes_direct-eng�php#sc6

Contains TX IC: 216QEbzzMU

Содержание DiveCAN Petrel 1







































































Отзывы:

Нет отзывов