background image

All written and visual data contained in this document reflects the latest product information available at the time of publication. 

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 310884

SHARPE MANUFACTURING • P.O. BOX 1441, MINNEAPOLIS, MN 55440-1441

1-800-742-7731, www.sharpe1.com

Copyright 2004, Graco Inc. is registered to ISO 9001

Revised 02/2011

Warranty

The manufacturer warrants the product manufactured by it, when properly installed, operated, applied, and maintained in accor-
dance with procedures and recommendations outlined in manufacturer’s instruction manuals, to be free from defects in material or 
workmanship for a period as specified below, provided such defect is discovered and brought to the manufacturer’s attention within 
the aforesaid warranty period.

The manufacturer will repair or replace any product or part determined to be defective by the manufacturer within the warranty 
period, provided such defect occurred in normal service and not as a result of misuse, abuse, neglect or accident. Normal mainte-
nance items requiring routine replacement are not warranted. The warranty covers parts and labor for the warranty period unless 
otherwise specified. Repair or replacement shall be made at the factory or the installation site, at the sole option of the manufac-
turer. Any service performed on the product by anyone other than the manufacturer must first be authorized by the manufacturer.

Unauthorized service voids the warranty and any resulting change or subsequent claim will not be paid. Products repaired or 
replaced under warranty shall be warranted for the unexpired portion of the warranty applying to the original product.

The foregoing is the exclusive remedy of any buyer of the manufacturer’s product. The maximum damages liability of the manufac-
turer is the original purchase price of the product or part.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER WRITTEN, ORAL, 
OR SATUTORY, AND IS EXPRESSLY IN LIEU OF THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE IMPLIED 
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. THE MANUFACTURER SHALL NOT BE LIABLE FOR LOSS OR 
DAMAGE BY REASON OF STRICT LIABILITY IN TORT OR ITS NEGLIGENCE IN WHATEVER MANNER INCLUDING DESIGN, 
MANUFACTURE OR THE INSPECTION OF THE EQUIPMENT OR ITS FAILURE TO DISCOVER, REPORT, REPAIR, OR MOD-
IFY LATENT DEFECTS INHERENT THEREIN.

THE MANUFACTURER, HIS REPRESENTATIVE OR DISTRIBUTOR SHALL NOT BE LIABLE FOR LOSS OF USE OF THE 
PRODUCT OR OTHER INCIDENTL OR CONSEQUENTIAL COSTS, EXPENSES, OR DAMAGES INCURRED BY THE BUYER, 
WHETHER ARISING FROM BREACH OF WARRANTY, NEGLIGENCE OR STRICT LIABILITY IN TORT.

The manufacturer does not warrant any product, part, material, component, or accessory manufactured by others and sold or sup-
plied in connection with the sale of manufacturer’s products.

Warranty Period
Parts and labor for two (2) from the date of shipment from the factory; heat exchangers are covered (parts only) for an additional 
three (3) years (total of five [5]). On units that manufacturer requests be returned to the factory, a one time removal/reinstallation 
labor allowance as noted in the Service Warranty Policies and Procedures Handbook will apply. Freight to the factory from the 
installation site and to the installation site from the factory will be paid by the manufacturer; means of transportation to be specified 
by the manufacturer.

AUTHORIZATION FROM THE SERVICE DEPARTMENT IS NECESSARY BEFORE MATERIAL IS RETURNED TO THE FAC-
TORY OR IN-WARRANTY REPAIRS ARE MADE.

Product Registration

Thank you for the purchase of your Sharpe

®

 product. We greatly appreciate your business.

Important reasons to register your product:

Registration enables Sharpe to notify you if there is a problem with your product.

Improved Product Development - Your input helps us continue to design products that meet your needs.

For the most up-to-date information and to register your product, please go to www.sharpe1.com and click on 
“Register Product.”

Содержание 6880

















Отзывы: