Sharp TMV Series Скачать руководство пользователя страница 32

Страница: 32 / 105

(2) Replacement of Speed Change Belt (as shown in Figure 18):

Refer to Step a to e of motor dismantling on P. 31.

Take off draw bar (I).

Dismantle the three hexagonal concave bolts (j) and use two of them (j) to life the bearing

housing (K).

Remove from top the two hexagonal concave bolts (L), fixing the speed change plate, and
take off the bolt sleeves (M).

Dismantle four hexagonal concave bolts (N)(O) and the two at the bottom (P).

Take off the two hexagonal concave bolts (S) speed change housing (Q) and gear housing (R).

Use a mallet and hit the upper belt housing (T) lightly so that it will break away from the fix
pin (U) for dismantling of the upper belt housing.

When the speed change belt is replaced accordingly, restore the machine by reversing the

orders.

Note: The replaced speed change belt shall conform to that of out company specifications.

Содержание TMV Series










































































































Результаты поиска

Содержание TMV Series

Отзывы:

Похожие инструкции для TMV Series

Бренды по названию

Популярные бренды

Sharp TMV Series, Руководство по обслуживанию и запасным частям

Результаты поиска

Содержание TMV Series

Отзывы:

Похожие инструкции для TMV Series

Бренды по названию

Популярные бренды