Sharp SF-DM11 Скачать руководство пользователя

Страница: 83 / 141

6. Duplex copy unit

Paper feed

roller

Takeup roller

Remove the double side copy tray.

Remove the front cover (2 screws).

Unfasten two connectors.

Remove the pivot holding plate screw (one each on both sides).

Remove the upper and transport paper guides from ADU.

Remove the clutch stopper plate
(1 screw).

Remove the clutch side E-ring.

Move the bushing and take out the paper
feed roller drive shaft onto the front frame side.

Remove the paper feed roller.

Remove the front and rear side two
counter roller tension springs.

Front frame Rear frame

Spring color

Black

White

Spring tension

Strong

Weak

Remove the counter roller.

Remove the clutch retaining plate
(1 screw).

Loosen the setscrew and remove the
clutch.

Remove the takeup roller drive shaft
(2 on front, 1 on rear).

Push down the spring holder and remove
the takeup roller unit from ADU.

Remove the takeup roller arm side E-ring
(rear side).

Remove the paper holder arm side E-ring
(front and rear).

Remove the takeup roller.

Counter

roller

Install the assembly so the
protrusion on the clutch spring
faces down. The protrusion
should never face the transport
path.

NOTE:

Remove the spring (2pcs.)

Remove the reversing roller.

6 – 11

Содержание SF-DM11














































































































































Результаты поиска

Содержание SF-DM11

Отзывы:

Похожие инструкции для SF-DM11

Бренды по названию

Популярные бренды

Sharp SF-DM11, Руководство по обслуживанию

Результаты поиска

Содержание SF-DM11

Отзывы:

Похожие инструкции для SF-DM11

Бренды по названию

Популярные бренды