Sharp SF-DM11 Скачать руководство пользователя | Manualshive

Страница: 111 / 141

background image

(3) Adjustment of AE sensor level

1

Perform Simulation 47. (The mirror base makes scanning motion
and stops at AE sensor level measuring position).

2

Place four or five A3-size (or 11" x 17") papers one upon another
on the original table.

3

Press the print switch again. The copy quantity indicator shows
the AE sensor output level for blank paper, which is stored in
memory.

(4) Setting of drum sensitivity

1

Perform Simulation 26-07 and check that the first digit of the
4-digit drum number printed on the front-frame sided drum flange
is shown on the copy quantity indicator.

2

If the indicated number differs from the drum number, press the
copy quantity key to change the setting.

Note: If the setting is done with the copy quantity key, the indi-

cated number is limited to 1, 2 or 3.

(5) Setting of test chart

1

Align four or five papers with at least 120 mm in width and ap-
prox.420 mm in length one upon another.

2

Set the test chart (UKOG-0162FCZZ) on exposure glass towards
machine front side as shown.

UKOG-0162FCZZ
DENSITY No.

1

2

3

4

5

6

7

8

9

10

W

UKOG-0089CSZZ
DENSITY No.

0.1

0.2

0.3

0.5 1.9

0

KODAK GRAY
SCALE

1

2

3

4

19

A

SHARP CORPORATION

MADE IN JAPAN

(6) Adjustment of copy density

A. Checking the developing bias output

Check that the output value is –150 V when the exposure is set to
"1" in the manual exposure mode. Perform Simulation 8-01 for
checking the developing bias.

B. Adjusting the density in manual exposure mode

1

Perform Simulation 46-01 for adjusting the copy density.
The exposure indicator of the operation panel shows "1" of the
manual copy mode.

2

Check that the cursor is on ME.1.
IF the cursor is not on ME.1, use

➡

message scroll key to

select ME.1.

3

Make a copy.
Check that the "6" of UKOG-0162FCZZ (or 0.5 of UGOG-
0089CSZZ) has slightly copied and "5"(0.3) is not copied.

<When light> Decrease the value shown on the copy quantity

indicator.

<When dark> Increase the value shown on the copy quantity

indicator.

*

available values : 1-99

ME1

ME5

TS1

TS5

PE1

PE5

AE1

AE5

AT1

AT5

4

When the copy density meets the above requirement, press

➡

key to highlight "ME5:".

UKOG-0162FCZZ

1

10

W

2

3

4

5

6

7

8

9

Not copied

Slightly copied

1

10

W

2

3

4

5

6

7

8

9

7 – 18

«
...
109
110
111
112
113
...
»

Содержание SF-DM11














































































































































Отзывы:

Нет отзывов

Похожие инструкции для SF-DM11

Бренд: Xerox Страницы: 89

Бренд: QMS Страницы: 2

WorkCentre Pro 421

Бренд: Xerox Страницы: 4

WorkCentre Pro 412

Бренд: Xerox Страницы: 212

WORKCENTRE PE 220

Бренд: Xerox Страницы: 8

WORKCENTRE PE 220

Бренд: Xerox Страницы: 2

WORKCENTRE PE 220

Бренд: Xerox Страницы: 200

WorkCentre m940

Бренд: Xerox Страницы: 86

Бренд: Xerox Страницы: 24

WorkCentre PE16

Бренд: Xerox Страницы: 201

WorkCentre M24 Color

Бренд: Xerox Страницы: 441

WORKCENTRE C2424

Бренд: Xerox Страницы: 2

WorkCentre M118

Бренд: Xerox Страницы: 5

WORKCENTRE C2424

Бренд: Xerox Страницы: 16

WORKCENTRE C2424

Бренд: Xerox Страницы: 20

WORKCENTRE C2424

Бренд: Xerox Страницы: 25

2006NPC - DocuColor Color Laser

Бренд: Xerox Страницы: 4

WorkCentre XK50cx

Бренд: Xerox Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды