manualshive.com logo in svg

Sharp R-420EK, Руководство по обслуживанию


Поделиться
Скачать
background image

17

R-420EK

WARNING : The oven should be fully assembled before following procedure.
(1) Place one cup of water in the center of the turntable tray in the oven cavity.
(2) Close the door, touch the " steaks / chops " pad once.
(3) The oven is in Compu Defrost cooking condition.
(4) The oven will operate as follows

1ST STAGE

2ND STAGE

WEIGHT

LEVEL

TIME

LEVEL

TIME

0.5lb

60%

25sec.

40%

20sec.

6. Re-install the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.

TEST PROCEDURES

PROCEDURE

LETTER

COMPONENT TEST

1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power transformer.
5. Ensure that these leads remain isolated from other components and oven chassis by using insulation

tape.

6. After that procedure, re-connect the power supply cord.
7. Remove the outer case and check voltage between Pin No. 1 of the 2 pin connector (A) and the

common terminal of the relay RY1 on the control unit with an A.C. voltmeter.
The meter should indicate 120 volts, if not check oven circuit.

RY1 and RY2 Relay Test

These relays are operated by D.C. voltage
Check voltage at the relay coil with a D.C. voltmeter during the microwave cooking operation.

DC. voltage indicated ............. Defective relay.
DC. voltage not indicated ........ Check diode which is connected to the relay coil. If diode is good,

control unit is defective.

RELAY SYMBOL

OPERATIONAL VOLTAGE

CONNECTED COMPONENTS

RY1

Approx. 24.3V D.C.

Oven lamp / Turntable motor / Cooling fan motor

RY2

Approx. 23.4.V D.C.

Power transformer

  8. Disconnect the power supply cord, and then remove outer case.
  9. Open the door and block it open.
10. Discharge high voltage capacitor.
11. Reconnect all leads removed from components during testing.
12. Re-install the outer case (cabinet).
13. Reconnect the power supply cord after the outer case is installed.
14. Run the oven and check all functions.

L

COMPU DEFROST TEST

                                               Key Unit

K

RELAY TEST

G 9

G10

G11

G12

G13

G14

G 8

G 7

G 6

G 5

G 4

G 3

G 2

G 1

CHICKEN

PIECES

STEAKS

CHOPS

RICE

MINUTE

PLUS

CHICKEN

BREAST

KEEP WARM

PLUS

POWER

LEVEL

CUSTOM

HELP

START

BEVERAGE

STOP

CLEAR

BAKED

POTATOES

POPCORN

FRESH

VEGETABLES

FROZEN

VEGETABLES

REHEAT

SENSOR

FISH 

SEAFOOD

FROZEN

ENTREES

FROZEN

ROLLS

MUFFINS

FRESH

ROLLS

MUFFINS

GROUND MEAT

(SENSOR COOK)

GROUND MEAT

(COMPU DEFROST)

5

4

3

2

1

0

9

8

7

6

TIMER

CLOCK

Содержание R-420EK













































Отзывы:

Нет отзывов

Похожие инструкции для R-420EK

Parkinson Cowan ACCLAIM User Manual preview
ACCLAIM
Бренд: Parkinson Cowan Страницы: 12
Maytag MMC5080AAB Owner'S Manual preview
MMC5080AAB
Бренд: Maytag Страницы: 22
NEFF B56CT64.0 Instruction Manual preview
B56CT64.0
Бренд: NEFF Страницы: 52
Cafe CVM517P4MW2 Dimensions And Installation Information preview
CVM517P4MW2
Бренд: Cafe Страницы: 2
Baumatic BSDO69 Installation And Instructions For Use preview
BSDO69
Бренд: Baumatic Страницы: 20
GE JEG3002BBE Manual preview
JEG3002BBE
Бренд: GE Страницы: 44
SAIKO TO-60E Instruction Manual preview
TO-60E
Бренд: SAIKO Страницы: 9
Concept2 ETV7160 Manual preview
ETV7160
Бренд: Concept2 Страницы: 80
Jenn-Air JJW9527 Guide Manual preview
JJW9527 Guide
Бренд: Jenn-Air Страницы: 24
Fagor 3MWB-25BTCGX Instruction Manual preview
3MWB-25BTCGX
Бренд: Fagor Страницы: 68
Koryo KOT 1921 User Manual preview
KOT 1921
Бренд: Koryo Страницы: 16
NEFF B64CS71 0B Series User Manual And Installation Instruction preview
B64CS71 0B Series
Бренд: NEFF Страницы: 44
V-ZUG BCXSLPZ60 Operating Instructions Manual preview
BCXSLPZ60
Бренд: V-ZUG Страницы: 52
RAMTONS RM 396 Instructions Manual preview
RM 396
Бренд: RAMTONS Страницы: 12
FAURE FSG25249XA User Manual preview
FSG25249XA
Бренд: FAURE Страницы: 37
GE Advantium PSB9240BL Installation Instructions Manual preview
Advantium PSB9240BL
Бренд: GE Страницы: 32
Orbegozo MIG 2045 Instruction Manual preview
MIG 2045
Бренд: Orbegozo Страницы: 52
Samsung MS19M8020TS/AA User Manual preview
MS19M8020TS/AA
Бренд: Samsung Страницы: 80

Бренды по названию

Популярные бренды

Загрузить еще бренды