Sharp R-380A Скачать руководство пользователя страница 24

Страница: 24 / 40

R-380A

HIGH VOLTAGE RECTIFIER AND HIGH VOLTAGE CAPACITOR REMOVAL

1. CARRY OUT 3D CHECKS.
2. Disconnect the brown and blue wires of power supply

cord from the noise filter.

3. Disconnect the connector of the main wire harness

from the noise filter.

4. Remove one (1) screw holding the noise filter angle to

the oven cavity rear plate.

5. Remove one the noise filter angle with noise filter from

the oven cavity rear plate.

6. Disconnect the high voltage of the high voltage rectifier

assembly from the power transformer.

7. Remove one (1) screw holding capacitor holder to the

oven cavity rear plate.

8. Disconnect rectifier terminal from capacitor.

Rectifier and high voltage assembly is now free.

9. Remove one (1) screw holding high voltage rectifier

assembly to capacitor holder.

10.Disconnect wire leads from capacitor and remove

capacitor holder.

11.High voltage rectifier assembly and high voltage

capacitor are free now.

CAUTION: WHEN REPLACING HIGH VOLTAGE

RECTIFIER AND HIGH VOLTAGE CAPACITOR,
GROUND SIDE TERMINAL OF THE HIGH VOLTAGE
RECTIFIER MUST BE SECURED FIRMLY WITH A
GROUNDING SCREW.

MAGNETRON REMOVAL

Removal
1. CARRY OUT 3D CHECKS.
2. Disconnect wire leads from magnetron.
3. Remove the two (2) screws holding chassis support to

oven cavity front plate and magnetron.

4. Remove the chassis support from oven.
5. Carefully remove the two (2) screws holding magnetron

to waveguide flange.

6. Lift up magnetron with care so that magnetron antenna

is not hit by any metal object around antenna.

7. Now, the magnetron is free.
Re-install
1. Re-install the magnetron to waveguide flange with the

two (2) screws diagonally as shown in Figure C-1.

2. Insert the two (2) tabs of the chassis support to the oven

cavity front plate and back plate.

3. Re-install the chassis support to oven cavity front plate

and magnetron with the two (2) screws.

4. Reconnect the wire leads to the magnetron. Refer to

"PICTORIAL DIAGRAM".

5. Re-install outer case and check that the oven is

operating properly.

CAUTION: WHEN REPLACING MAGNETRON, BE

SURE THE R.F. GASKET IS IN PLACE AND
MOUNTING SCREWS ARE TIGHTENED
SECURELY.

SCREWS

WAVEGUIDE
FLANGE

MAGNETRON

Figure C-1. Magnetron replacement

1. CARRY OUT 3D CHECKS.
2. Pushing the lever of positive lock

connector.

3. Pull out the positive lock

connector.

CAUTION: WHEN YOU (SERVICE ENGINEERS) CON-

NECT THE POSITIVE LOCK

CONNECTORS

TO THE TERMINALS, CONNECT THE POSI-
TIVE LOCK

SO THAT THE LEVER FACE

YOU (SERVICE ENGINEERS).

POSITIVE LOCK

CONNECTOR REMOVAL

Terminal

Push

Pull down

Lever

Positive lock

connector

Figure C-2. Positive lock

connector

1. Open covers of the terminal insulator by using small flat

type screw driver.

2. Remove the receptacle from the terminal insulator.
3. Now, the terminal insulator is free.

Installation
1. Insert the receptacle into terminal insulator.
2. Close covers of the terminal insulator, as shown

illustlated below.

TERMINAL INSULATOR REPLACEMENT

RECEPTACLE

COVERS

Terminal
insulator

Flat type
screw driver

Содержание R-380A









































Результаты поиска

Содержание R-380A

Отзывы:

Похожие инструкции для R-380A

Бренды по названию

Популярные бренды

Sharp R-380A, Руководство по обслуживанию

Результаты поиска

Содержание R-380A

Отзывы:

Похожие инструкции для R-380A

Бренды по названию

Популярные бренды