Sharp R-380A Скачать руководство пользователя страница 10

Страница: 10 / 40

R-380A

Home fuse blows when power
supply cord is plugged into wall
outlet.

FUSE M8A blows when power
supply cord is plugged into wall
outlet.

Display does not show any-
thing when power supply cord
is plugged into wall outlet.

Display does not operate prop-
erly when STOP/CLEAR pad
is touched.

Oven lamp does not light at
door opened. (Display ap-
pears.)

Oven does not start when the
START pad is touched. (Dis-
play appears)

Oven lamp does not light (Dis-
play appears.)

Fan motor does not operate.
(Display appears.)

Turntable motor assembly does
not operate. (Display appears.)

Oven or any electrical parts
does not stop when cooking
time is 0 or STOP/CLEAR pad
is touched.

Oven seems to be operating
but little or no heat is produced
in oven load. (Microwave power
level is set at HIGH)

Oven does not seems to be
operating properly when ME-
DIUM HIGH, MEDIUM, ME-
DIUM LOW or LOW is set.
(Oven operates properly at
HIGH and then the STOP/
CLEAR pad is touched the oven
stops.)

Oven goes into cook cycle but
shuts down before end of cook-
ing cycle.

Oven stops as soon as when
the START pad is touched.

AH sensor does not end during
Sensor Cooking condition.
(Oven does not shut off after a
cup of water is boiling by sen-
sor cooking.

Oven stops at 16 sec. after
starting.

TEST PROCEDURE

CK = Check / RE = Replace

POSSIBLE CAUSE

AND

DEFECTIVE PARTS

CONDITION

PROBLEM

ON
CONDITION

OFF
CONDITION

MAGNETRON

POWER TRANSFORMER

H.V. RECTIFIER ASSEMBLY

HIGH VOLTAGE CAPACITOR

1ST. LATCH SWITCH

2ND. LATCH SWITCH

STOP SWITCH

MONITOR SWITCH

MONITOR RESISTOR

THERMAL CUT-OUT 95˚C /125˚C

FAN MOTOR

TURNTABLE MOTOR

FUSE M8A

TOUCH CONTROL PANEL

KEY UNIT

RELAY (RY-1, RY-2)

FOIL PATERN ON P.W.B.

POWER SUPPLY CORD

SHORTED WIRE HARNESS

OPENED WIRE HARNESS

OVEN LAMP OR SOCKET

WALL OUTLET

MISADJUSTMENT SWITCH

HOME FUSE OR BREAKER

BLOCKED COOLING FAN

BLOCKED VENTILATION

NOISE FILTER

AH SENSOR

SENSOR
COOKING
CONDITION

A B C D E E E E G F H H I K L M N

RE CK CK RE CK CKCK CK CK

J O

Содержание R-380A









































Результаты поиска

Содержание R-380A

Отзывы:

Похожие инструкции для R-380A

Бренды по названию

Популярные бренды

Sharp R-380A, Руководство по обслуживанию

Результаты поиска

Содержание R-380A

Отзывы:

Похожие инструкции для R-380A

Бренды по названию

Популярные бренды