<P=005>
TROUBLESHOOTING
■
If a problem occurs
If this unit functions abnormally during operation, first check the following items. If the unit continues to function abnormally,
or if an abnormality appears other than listed below, turn off the player’s power and disconnect the AC power plug, then
consult your SHARP dealer or service personnel.
●
General
SYMPTOM
POSSIBLE CAUSE
REMEDY
●
The clock is wrong.
●
Did a power failure occur?
●
Try setting it again.
●
When a button is pressed,
the unit does not respond.
●
Turn the power off and on again, and
then retry the operation.
●
No sound is heard.
●
Is the volume level is set to "0"?
●
Are the headphones connected?
●
Increase the volume level.
●
Disconnect the headphones.
●
Radios make unusual noise
or the picture on the TV
screen is distorted.
●
When a radio or TV which uses an indoor
aerial is placed near the unit, the picture
on the TV screen may be distorted or the
radio may not function properly.
●
It is recommended that you use an ex-
ternal aerial.
●
CD playback
SYMPTOM
POSSIBLE CAUSE
REMEDY
●
Even though a disc has been
loaded, "NO DISC" or "ERROR"
is displayed.
●
Playback stops in the middle of
a track, or playback is not per-
formed properly.
●
Playback sounds are skipped.
●
The disc is loaded up-side down.
●
The disc is very dirty.
●
The disc which does not satisfy the stand-
ards.
●
Is the unit located near excessive vibra-
tions?
●
Has condensation formed inside the unit?
●
Load the disc with the correct side up.
●
Clean the disc.
●
Load the correct disc.
●
Place the unit on a firm, level surface free from
vibration.
●
Remove the disc and leave the power turned
on. The unit should function properly in about
1 hour.
●
MD recording and playback
SYMPTOM
POSSIBLE CAUSE
REMEDY
●
A re c or di n g c an n o t be
made.
●
Is the MiniDisc protected against accidental
erasure?
●
Did you try to make recording on a playback-only
MiniDisc?
●
Can you see the "TOC FULL" message in the dis-
play?
●
Slide the accidental erase prevention tab back
to its original position.
●
Replace it with a recordable disc.
●
Put in another recordable disc with recording
space on it.
●
Even though a disc has been
loaded, "NO DISC" or "ERROR"
is displayed.
●
Pl a y b a c k s o u n d s a re
skipped.
●
The disc is very dirty.
●
Is the unit located near excessive vibra-
tions?
●
Has condensation formed inside the unit?
●
Clean the disc.
●
Place the unit on a firm, level surface free from
vibration.
●
Remove the disc and leave the power turned
on. The unit should function properly inabout 1
hour.
●
Radio reception
SYMPTOM
POSSIBLE CAUSE
REMEDY
●
Radios make unusual noise
consecutively.
●
When the unit receives a radio broadcast near
a TV set, a computer or a wordprocessor, it
may pick up noise. If this happens, try to move
the unit from the place where the noise is
picked up.
●
The preset channel cannot
be called.
●
Did a power failure occur?
●
Preset the channel again.
●
Remote control
SYMPTOM
POSSIBLE CAUSE
REMEDY
●
The remote control does
not function or does not
operate properly.
●
The batteries (polarity) are not inserted properly.
●
The batteries inside the remote control are dead.
●
The remote control is operated from an incorrect
distance or angle.
●
Insert properly.
●
Replace the batteries.
●
Operate it within a range of 0.2 m (8")
to 6 m (20’) and within an angle of 15
°
to either side of centre.
●
The power cannot be turned on
from the remote control.
●
Is the AC power lead plugged in?
●
Connect the AC power lead.
MD-ZV30H TINSZ0217AWZZ
E-40
