Sharp LC-90Y8T Скачать руководство пользователя страница 51

Страница: 51 / 67

LC-90Y8T

6 – 10

No sound from external output device (7)

Does not the sound of the audio signal output to HDMI1 go out?

Does audio signal output from pin[14] of SC1501 (HDMI1 terminal) ?

YES

Check SC1501 and peripheral circuits.

Does audio signal output from pin[39/HECP] of IC2601(HDMI-SW) ?

YES

Check the line between IC2601 and SC1501.

Does audio signal input to pin[36/HDMI̲ARC̲SPDIF] of IC2601 ?

YES

Check IC2601 and peripheral circuits.

Does audio signal(HDMI̲OPT̲OUT) output from pin[Y32/
CPU̲ASPDIF1] of IC3301(Digital AV decode & Main CPU)?

YES

Check the line between IC3301 and IC2601.

Check IC3301 and its peripheral circuits.

No picture on the display (1)

The picture doesn't appear in all modes.

Is the signal output from IC3301(DIGITAL̲AV̲DECODER̲&̲MAIN̲CPU) respectively?
[VBO̲TXA+-(AT4/AU4), VBO̲TXB+-(AP3/AR3), VBO̲TXC+-(AT2/AU2), VBO̲TXD+-(AR1/AR2)]

YES

Check IC3301 and its peripheral control circuits.
(IC2004, IC3501, IC3502, IC3503, IC3504, X3301, etc.)

Do above-mentioned signals output from connector
(SC3801) ?

Check the line between IC3301 and SC3801.

YES

Similarly, is LCD controller's control signal normal ?

Please check each control signal of DET̲POW(DET̲PNL12V),

PE(PNL̲EN).

YES

LCD Controller Unit:
Do signals input to connector(LW) of LCD Controller Unit ?

Wire harness (LV) is checked.

YES

Check the panel module.

Содержание LC-90Y8T




































































Результаты поиска

Содержание LC-90Y8T

Отзывы:

Похожие инструкции для LC-90Y8T

Бренды по названию

Популярные бренды

Sharp LC-90Y8T, Руководство по обслуживанию

Результаты поиска

Содержание LC-90Y8T

Отзывы:

Похожие инструкции для LC-90Y8T

Бренды по названию

Популярные бренды