en-15
en-16
KN-H24VNA
KN-H24VNA
TIMER
CARE AND CLEANING
1
2
①
Select the category [2].
②
Confirm the category [2].
Select the menu [18].
Before operating, make sure to connect the power cord correctly.
Begin to set the cooking mode.
Confirm [AUTO].
Set the menu number. (See page en-11)
①
②
The appliance can complete cooking at a preset time (in maximum 12hours)
The Timer cooking can be used for the AUTO menus which the
TIMER
button lamp flashes
during setting the menu number. There are two memory banks for the Timer cooking.
2
Select the memory bank and enter the cooking completion time.
.
Enter the time.
The time can be set in 10 minutes intervals.
(The time setting will be saved in the memory bank)
Select the memory bank 2.
The preset time [18:00] will flash.
3
Start Timer cooking.
・
The
TIMER
button lamp will be lit.
・
Heating starts as soon as you press the
START
button, and the food will be ready to eat at the set time.
・
The appliance will automatically switch to Keep Warm
(for 12 hours) after the cooking is complete.
After use, turn the appliance off. Unplug and then remove the inlet plug from the main unit.
1. If you attempt to start the appliance with a Timer setting exceeding the maximum of
12 hours, you will hear a notification sound and the display will return to a time
where using Timer is possible.
2. If you start the appliance with a Timer setting that is shorter than the required cooking
time, cooking will start immediately and you will see the approximate time left until
cooking is complete.
(In this case, the appliance will not switch to Keep Warm after cooking is complete)
NOTES :
Do not use the pot if the handle is loose. There is a risk of the pot falling
and causing burns. Tighten the screws on the under side of the handle before use.
Screws
If the handle becomes loose
Do not wash the outside or the inside water
level mark with cream cleanser with or even
without a soft sponge.
*Use citric acid that is generally available in pharmacies etc. (without additives or over 99.5%).
Lemon juice can be used instead of citric acid.
Inner pot/Drip tray
Mix 1 teaspoon of citric acid and a little salt with 1 tablespoon of water, apply on
a soft sponge and rub. Rust can be difficult or impossible to remove completely.
*
These are caused by elements contained in water and are not harmful to humans.
You can use the pot as it is.
If it bothers you, mix 1 teaspoon of citric acid with 1 tablespoon of water, apply
on a soft sponge and rub.
*
Outside
Water level mark
Press once
：
TIMER 1 (preset time: 6:00)
Press twice
：
TIMER 2 (preset time: 18:00)
* Suppose you want to set AUTO menu [2-18] ratatouille in the memory bank 2 as the
cooking completion time is 18:30.
Before cleaning, turn the appliance off. Unplug and then remove the inlet plug from the main unit.
Make sure the cavity including the temperature sensor and thermo plate, each parts and
accessories are completely cool.
Do not use commercial cleaners, abrasive, harsh cleaners, solutions that contain sodium
hydroxide, or scouring pads on any part of the appliance. Dishwashers cannot be used to clean
the appliance.
NOTE :
NOTE :
Cleaning tips
●
Clean after every use.
●
Remove the drip tray after taking the inner pot out.
●
Wash with mild soap or detergent solution using a soft sponge. Rinse and dry thoroughly.
Water may leave trace minerals, which make it easier for iridescent or white
discoloration to form. Water may also cause rusting.
Heavy dirt
Iridescent or white
discoloration
When the pot has
become rusty
Rinse carefully after washing
Soak with hot water and rub with a sponge.
Baking soda can be used for stubborn stain.
Put 10g of baking soda per 200mL of water in the inner pot, and set the appliance
with MANUAL [1-2] for 10 minutes.
After heating, leave the inner pot for a few hours. Then rub with a soft sponge.
(Be careful not to get burned with the hot water after heating)
Key Point - Clean immediately if it is dirty!
❶
❸
❷
❹
(KN-H24VNA).indb 15
2017/02/24 16:03:23
