background image

ENGLISH

E-9

outlet.

2

Filter Installation

1

After the HEPA Filter is removed
from the plastic bag, place it
within the Filter Frame with the
tabs facing up.

(See the diagram to the right.)

Ensure that the filter is installed correctly.
Do not install the filter backwards or the
unit will not operate properly.

2

After removing the Active Car-
bon Filter from the plastic bag,
place it within the Filter Frame
on top of the HEPA Filter.

(See the diagram to the right.)

3

Next, place the Filter Separator
and then the Pre-Filter within
the Filter Frame.

• Place the Filter Sepa-

rator so that the ribs
are facing down as
shown in the diagram
on the right.

• Insert the tabs, (4), of

the Pre-Filter into the
associated holes
found on the Filter
Frame.

• Mount the Filter Frame as shown in the

diagram to the right to the main unit.

4

Fill in the usage start date on
the Date Label, which can be
found on upper left corner of
the Main unit. Mount the Front
Panel to the Main Unit.

Use the date as a guide for your Filter
Replacement schedule.

Tabs

HEPA Filter

Filter Frame

Active Carbon Filter

HEPA Filter

Filter Frame

Pre-Filter

Tabs (4 places)

Filter Separator

Active Carbon
Filter

Holes

Filter Frame

Filter Frame

Date Label

Rib of the Filter Separator

Содержание FU-60SE-P





















Отзывы: