21
8
Common non-fault phenomenon (Please refer to
this section if there is an abnormality happens.)
Abnormal display
Display
U9
E4
E3
E2
C
＊
Washing machine inclines or is
shaky.
The clothing is lopsided.
The end of drain hose is blocked.
The drain position is
relatively high.
Top lid is not closed during spin
drying.
Possible non-fault cause
Solution
Low flow at the faucet.
Water inlet filter net is blocked.
It generates a beep when washing machine indicates abnormal display.
As the phenomenon may not be a fault,
please check it again before sending the machine for repair. In the case
of failure, please consult Sharp Service Center. Be sure not to disassemble and
repair the machine without permission.
Caution
There is a possibility
of malfunction.
The faucet is closed.
Top lid is opened
when the
reservation
course starts.
Drain hose is folded/crumpled/tied.
Increase water supply, press START/
PAUSE key.
Turn the faucet on, press START/
PAUSE key.
Clean the filter net, press START/
PAUSE key.
Close top lid.
Adjust drain hose properly, press
START/PAUSE key.
Clean drain hose, press START/
PAUSE key.
Level the washing machine by
adjusting the foot.
(
p.7
)
Distribute the clothing evenly.
Turn off the power and pull out Power
cable. After wait 1 minute,
turn on and operate.
Top lid is opened during
CHILD LOCK.
Turn the power off, and check inside
the tub
CHILD LOCK is not released, unless
you reset it manually.
Caution
E1
＊ : number
E
Cannot spin drying.
Adjust drain hose properly.(p.8)
Wait for 10 minutes, and press
START/PAUSE key.
19
Drain hose
Installation
See Installation manual for detail.
Install the drain hose
●
The inner diameter of the hose is about 3.8cm.
●
Make sure the drain hose is securely inserted into the drain outlet and firmly fixed.
If the hose comes off, that will lead to water leakage and damage to the floor.
Check if the drain outlet is not clogged before connetion
●
Check the drain outlet on a regular basis.
【
Drainning may take longer time or stop if the outlet is clogged.
】
1
2
1.5m or under
Make sure installing the drain hose horizontally.
(The height of the hose must be 10cm or under.)
【
Cause of operation stop and abnormal sound during spinning.
】
Use an extension hose.
The lenth of the exention hose must not exceed 1.5m.
(The inner diameter of the extension hose must be about 3.8cm or over.)
10cm or under
●
The height of hose is too high
●
The drain hose is kinked
●
The drain hose is too short
How to install properly
Cut the hose
diagonally.
(not easilyblocked)
Adjust the length by cutting the hose.
In case of using an underfloor drain outlet, cut the end of the hose diagonally.
详见安装手册
安装
排水软管
如果排水口堵塞，则排水时间可能延长或停止排水
定期检查排水口
安装排水软管
软管的内部直径约为3.8厘米
请确保排水管牢固地插入排水口并固定牢
如何正确安装
软管的高度太高
确保水平方向安装软水管（软水管的高度不得高于10厘米）
旋转时发出不正常声音及停止运作的原因
排水软管打结了
切断软管来调整长度。如果使用地下排水口，对角切断软管的端部。
对角切断软管（不易堵塞）
排水管太短
使用延长管，延长管的长度不得超过1.5米
（延长软管的内部直径必须不少于3.8厘米）
不超过1.5米
不超过10厘米
连接前请确保排水口无堵塞
