Sharp DW-E16FA, Руководство по эксплуатации

Страница: 16 / 32

E - 30 E - 31
TROUBLESHOOTING
(Continued)
—
—
E - 17
E - 25
—
—
—
Magnet
Float
Magnet: Facing up
Facing outside of tank
( (
(Back of the main unit)
Sensor
(inside)
Pin
E - 19
—
—
E - 20
E - 20
E - 30
E - 11
E - 11,20
E - 14
—
—
ODOR Indicator
Light does not
change its color
The operation stops
The unit cannot operate
Buttons do not work
The main unit falls down
(during dehumidifying or
laundry drying operation
or while water enters the
tank)
Other indicator
lights blinking
ODOR Indicator Light
does not turn green
ODOR Indicator Light
often switches
The AIR PURIFYING
indicator light does
not turn off
The float comes off
● After the operation starts, ODOR Indicator Light does not change its
color for the time being due to unsteady sensitivity of the sensor.
After a few minutes, sensitivity of the sensor becomes steady.
●
If ODOR Indicator Light remains green, the air is fresh.
It is hard for the sensor to detect in some places. It is normal if
ODOR Indicator Light changes its color when cigarette smoke is
blown to the sensor.
●
If the operation is started in a room with a strong odor, sensitivity of
the odor sensor may become blunt.
Please continue the air purifying operation (MED) for several
hours or 1 day.
● Dust may accumulate on the sensor.
Please remove the rear panel and
the filters and clean them with
a cleaner through the hole as
shown in the right figure.
Display
Float
The unit falls down
The unit does not operate
Problem
Solution Reference
Page
Problem
Solution Reference
Page
● It may not turn green due to dirt comes from outdoors when the window
or the door is opened frequently or the room is of poor airtightness.
●
The AIR PURIFYING indicator light cannot be turned off during
operation.
In all operation modes, air is purified through the HEPA filter and the
Active Carbon Deodorizing filter.
●
It may respond to wind and temperature change caused by opening
and closing of the door frequently.
● Install the float by following the procedure below.
TROUBLESHOOTING
1
Check the direction of float, and then
insert the float.
2
Insert pin and
secure.
● Check the CHILD LOCK setting.
If locked, release the child lock.
● The operation has stopped with the Auto Off function.
Press the OFF button to stop the indicator light from blinking,
and start the operation again.
When using continuously, disable the Auto Off function.
● The water tank becomes full and the operation has stopped with the
Auto Off function.
Empty the water tank, press the OFF button to stop the
indicator light from blinking, and start the operation again.
●
Laundry drying (Auto) operation has completed, and the operation
has stopped.
Press the OFF button to stop the indicator light from blinking, and
start the operation again.
● The unit may malfunction.
Please consult the store where you purchased the product or
SHARP authorized service center.
●
When the main unit falls down while water enters the tank, pull out
the power plug and consult the store where you purchased the
product or SHARP authorized service center.
●
Check the power plug.
If not inserted, insert the power plug into an outlet.
●
Check to see if there is a power outage.
If there is a power outage, wait until the power is resumed.
●
Check to see if the water tank is properly placed.
If not, place the water tank correctly.
●
Check to see if the water tank is full.
If the tank is full, drain the water.
●
Check to see if the float is properly placed.
If not, place the float properly.
Blinking (red)
Long beep
Long beep
Blinking
(green)
Blinking
(green)
Beep
Beep_
Long beep
Blinking
(red)
Blinking
(green)