E-11
Notes:
●
When radio interference occurs, auto scan tuning may
stop automatically at that point.
●
Auto scan tuning will skip weak signal stations.
●
To stop the auto tuning, press the TUNING (
or
)
button again.
To receive an FM stereo transmission:
●
Press the TUNER button to select stereo mode and
“
ST
”
indicator will be displayed.
“
”
and
“ ”
will
appear when an FM broadcast is in stereo.
●
If the FM reception is weak, press the TUNER button to
extinguish the
“
ST
”
indicator. The reception changes to
monaural, and the sound becomes clearer.
You can store 40 AM and FM stations in memory and recall
them at the push of a button. (Preset tuning)
Note:
The backup function protects the memorised stations for a
few hours should there be a power failure or the AC power
cord becomes disconnected.
Press the PRESET (
or
) button for less than 0.5
seconds to select the desired station.
The stations saved in the memory can be scanned
automatically. (Preset memory scan)
In this example, the clock is set for the 24-hour (0:00) display.
To confirm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 5 seconds.
Note:
When power supply is restored after unit is plugged in again
or after a power failure, reset the clock.
To readjust the clock:
Perform “Setting the clock” from step 1. If the “Clock” does not
appear in step 2, step 4 (for selecting the 24-hour or 12-hour
display) will be skipped.
To change the 24-hour or 12-hour display:
Listening to the radio (continued)
●
Manual tuning:
Press the TUNING (
or
) button repeatedly to
tune in to the desired station.
●
Auto tuning:
When the TUNING (
or
) button is pressed for
more than 0.5 seconds, scanning will start
automatically and the tuner will stop at the first
receivable broadcast station.
■
Memorising a station
1
Perform steps 1 - 3 in
“
Tuning
”
.
2
Press the MEMORY
button.
3
Within 30 seconds, press the PRESET (
or
) button
to select the preset channel number. Store the stations
in memory, in order, starting with preset channel 1.
4
Within 30 seconds, press the MEMORY button to store
that station in memory. If the
“
MEMORY
”
and preset
number indicators disappear before the station is
memorised, repeat the operation from step 2.
5
Repeat steps 1 - 4 to set other stations, or to change a
preset station. When a new station is stored in the
memory, the station previously memorised for that
preset channel number will be erased.
■
To recall a memorised station
■
To scan the preset stations
1
Press the PRESET (
or
) button for more than 0.5
seconds. The preset number will flash and the programmed
stations will be tuned in sequentially, for 5 seconds each.
2
Press the PRESET (
or
) button again when the desired
station is located.
Listening to the radio (continued)
■
To erase entire preset memory
1
Press the POWER ON/STAND-BY button to enter the stand-by mode.
2
While pressing down the
button, press the POWER ON/
STAND-BY button until
“
Tuner Clear
”
appears.
Setting the clock (Remote control only)
1
Press the POWER ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the ENTER button. To adjust
the day, press the
or
button and then press the
ENTER button.
4
Press the
or
button to select 24-hour or 12-hour
display and then press the ENTER button.
The 24-hour display will appear.
(0:00 - 23:59)
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
5
To adjust the hour, press the
or
button and then
press the ENTER button. Press the
or
button
once to advance the time by 1 hour. Hold it down to
advance continuously.
6
To adjust the minutes, press the
or
button and
then press the ENTER button. Press the
or
button once to advance the time by 1 minute. Hold it
down to advance the time by 5 minutes interval.
1
Clear all the programmed contents. [Refer to “Factory
reset, clearing all memory” on page 14 for details.]
2
Perform “Setting the clock” from step 1 onwards.
TUNING
POWER
