Sharp CD-PC3500, Руководство по обслуживанию

Страница: 7 / 68

– 7 –
CD-PC3500
OPERATION MANUAL
X-BASS/ DEMO
POWER
ON/
STAND-BY
RE
S
E
TTI
NG
THE
MI
CRO
CO
MP
UTE
R
Reset the microcomputer under the following conditions:
●
To erase all of the stored memory contents (clock and timer settings, and tuner and CD presets).
●
If the display is not correct.
●
If the operation is not correct.
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
While
pressing
down
the
b
u
tt
o
n
a
n
d
th
e
X-BASS/
DEM
O
button, hold down the ON/STAND-BY button for at least 1 second.
●
"CLEAR AL" will appear.
Caution:
●
The operation explained above will erase all data stored in memory including clock and timer settings, and tuner and CD presets.
S
E
TTI
NG
THE
CLO
CK
POWER
ON/
STAND-BY
CLOCK
MEMORY/SET
TUNING/ TIME ( )
In this example, the clock is set for the 12-hour (AM 12:00) sys- tem.
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Press the CLOCK button.
3
Within 5 seconds, press the MEMORY/SET button.
4
Press
the
TUNING/TIME
(
or
) button to select the time
display mode.
"AM 12:00"
→
T
h
e 1
2
-h
ou
r di
sp
la
y
w
ill
ap
pe
ar
.
(
A
M
1
2
:0
0
-
P
M
1
1
:5
9
)
"A
M
0:
00
"
→
Th
e 1
2
-h
ou
r di
sp
lay
w
ill
ap
pe
ar
.
(
A
M
0
:0
0
-
P
M
1
1
:5
9
)
"0
:0
0
"
→
T
h
e
24
-h
o
u
r d
isp
la
y w
ill
ap
pe
ar
.
(
0
:0
0
-
2
3
:5
9
)
●
Note that this can only be set when the unit is first installed or it has been reset (see page 21).
5
Press the MEMORY/SET button.
6
Press
the
TUNING/TIME
(
or
) button to adjust the hour.
●
Press
the
TUNING/TIME
(
or
) button once to advance
the time by 1 hour. Hold it down to advance continuously.
●
When the 12-hour display is selected, "AM" will change auto- matically to "PM".
7
Press the MEMORY/SET button.
8
P
re
s
s
th
e
TU
N
IN
G
/TI
M
E
(
o
r
) b
u
tt
o
n
to
a
d
ju
s
t
th
e
minutes.
●
Press
the
TUNING/TIME
(
or
) button once to advance
the time by 1 minute. Hold it down to change the time in 5 minute intervals.
●
The hour setting will not advance even if minutes advance from "59" to "00".
9
Press the MEMORY/SET button.
●
The clock starts operating from "0" second. (Seconds are not displayed.) And then the clock display will disappear after a few seconds.
To see the time display:
Press the CLOCK button.
●
The time display will appear for about 5 seconds.
Note:
●
The clock display will flash on and off at the push of the CLOCK button when the AC power supply is restored after a power failure occurs or after the AC power cord is disconnected. If this happens, follow the procedure below to change the clock time.
To change the clock time:
①
Press the CLOCK button.
②
Within 5 seconds, press the MEMORY/SET button.
③
Perform steps 6 - 9 above.
To change the time display mode:
①
P
e
rf
or
m
st
eps
1 -
2 in t
he sect
io
n
"R
E
S
E
TTI
N
G
T
H
E
MICROCOMPUTER", on page 21.
②
Perform steps 1 - 9 above.
(Main unit operation)
AM 12:00
AM 0:00
0:00
2 3 4
7
6
5
8 9