Sharp CD-C478, Руководство по обслуживанию

Страница: 18 / 80

CD-C478/478C
– 18 –
SP out L-ch Input signal is output.
(TMV01) R-ch Input signal is output.
(TMX11) SP out C-ch SP cut, no output
(TMX111) SP out S-ch Almost no output (only omitting component)
SP out L-ch Almost no output (only omitting component)
(TMV01) R-ch Almost no output (only omitting component)
(TMX11) SP out C-ch Input signal is output.
(TMX11) SP out S-ch Almost no output (only omitting component)
State of set Dolby Pro Logic Dolby Pro Logic On mode
Output point Bypass mode Normal mode Phantom mode
ICC01 12 pin L-out Output enabled state Output enabled state Output enabled state
11 pin R-out Output enabled state Output enabled state Output enabled state
ICC01 9pin C-out No output Output enabled state No output
ICC01 10pin S-out No output Output enabled state Output enabled state
SP OUT L-ch Output enabled state Output enabled state Output enabled state
(TMV01) R-ch Output enabled state Output enabled state Output enabled state
SP OUT C-ch No output in MUTE (Q604) state Output enabled state No output in MUTE (Q604) state
(TMX11)
SP OUT S-ch No output in MUTE (Q603) state Output enabled state Output enabled state
(TMX11)
EXPLANATION OF DOLBY SURROUND PRO LOGIC AND EVALUATION METHOD
Test tone output
• Pro Logic ON Normal mode
Press the remote control TEST TONE button.
→
Output of only L-ch
→
Output of only C-ch
↑
↓
Output of only S-ch
←
Output of only R-ch
The test tone (noise) is repeatedly output for output period
(2 sec).
In this case the following indication appears repeatedly.
→
TEST
→
L-ch
→
C-ch
↑
↓
S-ch
←
R-ch
• Pro Logic ON Phantom mode
Press the remote control TEST TONE button.
→
Output of only L-ch
→
Output of only R-ch
↑
↓
←
Output of only S-ch
The test tone (noise) is repeatedly output for output period
(2 sec).
In this case the following indication appears repeatedly.
→
TEST
→
L-ch
→
R-ch
↑
↓
←
S-ch
←
Outline
• Namely, two speakers are connected in parallel to one
amplifier.
• In the Pro Logic BYPASS mode the amplifier for C-ch (center
channel) and the amplifier for S-ch (surround channel) are in
MUTE state. The SP output is cut.
• In the normal mode of Pro Logic ON mode the amplifiers for
C-ch and S-ch are in operative state, so that the SP output
appears.
• In the Phantom mode of Pro Logic ON mode the amplifier for
C-ch is in MUTE state, so that the SP output is cut. The
amplifier for S-ch (surround) is in operative state, so that the
SP output appears
• State of element output and terminal output in specific mode
Relation between VIDEO IN input and output in Pro Logic
ON state
(1) L-ch/R-ch same phase input into VIDEO IN input jack in
VIDEO Function mode
Output point Normal mode
Output point Phantom mode
(2) L-ch/R-ch reverse phase input into VIDEO IN input jack in
VIDEO Function mode
(Reverse phase: Phase difference between L and R is 180°)
Output point Normal mode
SP out L-ch Almost no output (only omitting component)
(TMV01) R-ch Almost no output (only omitting component)
(TMX11) SP out C-ch Almost no output (only omitting component)
(TMX11) SP out S-ch Input signal is output.
Output point Phantom mode
SP out L-ch Almost no output (only omitting component)
(TMV01) R-ch Almost no output (only omitting component)
(TMX11) SP out C-ch SP cut, no output
(TMX11) SP out S-ch Input signal is output.
• Accordingly, if you want to output signal waveform to C-ch SP
out, give the same phase input into L-ch/R-ch INPUT in the
Pro Logic Normal mode.
If one of channels receives input, C-ch does not output. Only
L-ch or R-ch outputs.
• If you want to output signal waveform to S-ch SP out, you can
use either Normal mode or Phantom mode. However, 180°
reverse phase input must be given to L-ch/R-ch INPUT.