Sharp AX-GX2T(R) Скачать руководство пользователя страница 33

Страница: 33 / 60

7 – 2

5. Remove the two (2) screws holding the back plate to the rear

angle.

6. Remove the four (4) screws fixing the back plate.

7. Now, the back plate with exhaust cover is free.

[4] DOOR ASSEMBLY REPLACEMENT

1. REMOVAL

1. Disconnect the power supply cord.

2. Wait for 60 seconds to discharge the high voltage capacitors of the

inverter unit.

3. Remove the outer case cabinet, referring to “OUTER CASE

REMOVAL”.

4. Remove the dew tray

5. Disconnect the 12-pin connector of the control panel harness.

6. With the door open 45

, push the door cam down and back and

then slowly open the door to remove it.

7. With the door open more than 106

, slide the door left from the

hinge pin slot to remove it.

NOTE: Be careful not to make the 12-pin harness caught in the

square hole of the oven.

Be careful when installing the door, since the door cam is eas-
ily pulled in the back of the oven.

After replacing the door or loosening/removing the hinge
screws, make sure to adjust the door.

2. REINSTALL

1. To facilitate reinstallation, first put the hinge pin in the right hinge.

CAUTION: If bent, the comb-shaped teeth should be straighten (other-

wise, microwave leakage may result.)

After replacing or repairing the door, ensure that there is no
microwave leakage (otherwise, microwave leakage may
result).

Always make latch adjustment (otherwise, malfunction may
result)

3. After any service to the door

1) Make sure that the door sensing switch, the secondary interlock

switch and the monitor switch are operating properly. (Refer to
chapter “Test Procedure”.)

2) An approved microwave survey meter should be used to assure

compliance with proper microwave radiation emission limitation
standards.

[5] DOOR COVER REMOVAL AND DOOR PACKING INSTALLATION

1. DOOR COVER REMOVAL

1. Disconnect the power supply cord.

2. Wait for 60 seconds to discharge the high voltage capacitors of the

inverter unit.

3. Put a putty knife (thickness of about 0.5mm) into the gap between

the door cover and the door frame (for tab positions, refer to photo).
First disengage four(4) tags on the right side, four(4) tags on the left
side, and six(6) tags on the front side.

4. Lift up the this side of the door cover. And disengage the center tab

and the seven (7) tabs on the back side. If it is difficult to disengage
the seven (7) tabs on the back side, remove the door packing.

5. Remove the door packing from the door cover.

6. Following the above steps 3, 4 and 5 can remove the door cover

without breaking it.

NOTE: * Embed the entire circumference of the door packing in the

door cover and then fit the door packing with the door
frame.

* After assembling, press the entire circumference of the

door packing so that the door packing is in a uniform condi-
tion without protrusion.

* Be careful not to damage the surface.

* After assembling, check that there is no microwave/steam

leakage from the door.

2. DOOR PACKING INSTALLATION

1. Turn the door cover over.

2. Install the four (4) corners of the door packing into the four (4) cor-

ners of the door cover opening.

3. As the cross section of the door cover opening is T character type,

put the door packing over the door cover opening.

Panel R

Handle

Slide to left

Door Cam

106º

Door Cover

Door packing

This side

Positions of tabs

Right side

Left side

Door cover

Center tab

Magnified picture of the door packing

Groove of
the door packing

Door packing

Reverse side of the door cover

T character part of the door cover

Magnified picture of the door cover

Содержание AX-GX2T(R)





























































Результаты поиска

Содержание AX-GX2T(R)

Отзывы:

Бренды по названию

Популярные бренды

Sharp AX-GX2T(R), Руководство по обслуживанию

Результаты поиска

Содержание AX-GX2T(R)

Отзывы:

Бренды по названию

Популярные бренды