Sharp AR-M208, Руководство по обслуживанию, Страница: 26 / 180

AR-M208 SIMULATION 8 - 12
Operation/procedure
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
Setup of various copy conditions: Similar to the normal copy mode.
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTER-
RUPT] key is inhibited.
Operation/procedure
Used to adjust ON/OFF timing of the separation voltage.
Operation/procedure
Keep the OC cover open for execution of this test command.
If the adjustment is normally completed, the adjusted value is dis-
played and written into the EEPROM.
If the adjustment is abnormal, "ERR" is displayed and the value is not
written into the EEPROM.
For that which is not adjusted because of abnormality, "---" is dis-
played.
Operation/procedure
Enter a figure with the 10-key.
[When key input = 1]
Self print is performed in the 2-by-4 mode
Since scanning is not performed, if a document is set on the SPF, the
START key is invalid.
* Duplex print is invalid.
[When key input = 2]
Grid print is performed. (1cm, 1-dot width WLT/A3 print (A3 main scan,
WLT sub scan))
If the IMC board is not installed, key input cannot be made.
* Duplex print is allowed.
(Initial screen) (Input screen) (Executing screen)
Display items Content
Setting
range
Default Remark
1:BYPASS Manual feed 1-99 50 Tray selection:
Manual feed
cassette is
specified.
2:TRAY1 1st cassette 1-99 50 Tray selection:
1st cassette is
specified.
3:TRAY2 2nd cassette 1-99 50 Tray selection:
2nd cassette is
specified.
4:TRAY3 3rd cassette 1-99 50 Tray selection:
3rd cassette is
specified.
5:TRAY4 4th cassette 1-99 50 Tray selection:
4th cassette is
specified.
6:DUPLEX Back print 1-99 50 Tray selection:
Made by user.
7:SPF(SIDE1) SPF front
surface 1-99 50 Tray selection:
Made by user.
8:SPF(SIDE2) SPF back
surface Tray selection:
Made by user.
51-9
Purpose Adjustment
Function
(Purpose) Used to adjust ON/OFF timing of the separation
voltage.
Item Adjustment
(Initial screen) (Input screen)
Display
items
Content
Setting
range
Default
1:SHV ON Separation voltage ON timing
* Transfer V2ON reference
(synchronized with the
adjustment value of 50)
25-90 50
2:SHV OFF Separation voltage OFF timing
* Transfer V2OFF reference
(synchronized with the
adjustment value of 50)
50-90 75
Sim51-2 RESIST ADJ.
1:BYPASS
50
2:TRAY1 50
3:TRAY2 50
1/3
50
Sim51-9 SHV SETTING
1:SHV ON 50
2:SHV OFF 50
1
Sim51-9 SHV SETTING
1:SHV ON 50
[ 1- 99] 50
53
53-8
Purpose Adjustment
Function
(Purpose) Used to adjust the mirror unit SPF scan position
automatically.
For the SPF scan position auto adjustment, the mirror
unit is shifted to 11mm before the SPF glass cover
edge and is moved by self-boost, and images are
scanned in each step, and the position from the glass
cover edge is automatically detected.
[Adjustment value]
Default: 50 Setting range: 1 to 99
Adjustment unit 1 = about 0.127mm
(Initial screen) (Executing screen)
"EXEC" is highlighted during execution.
(Normal end screen) (Abnormal end display)
64
64-1
Purpose Operation test/check
Function
(Purpose) Self print
Key input = 1
Self print is performed in the 2-by-4 mode (2-line print
and 4-line non-print).
Key input = 2
Grid print is performed. (1cm, 1-dot width WLT/A3 print
(A3 main scan, WLT sub scan))
Section Printer
Item Operation
Sim53-8 SPF AUTO
PRESS OK KEY EXEC
Sim53-8 SPF AUTO
EXEC
Sim53-8 SPF AUTO
SPF STOP ADJ [ 47]
PRESS OK KEY EXEC
Sim53-8 SPF AUTO
SPF STOP ADJ [ERR]
PRESS OK KEY EXEC