manualshive.com logo in svg

Sharp AR-505, Руководство по эксплуатации

Поделиться
Скачать
Sharp AR-505 Скачать руководство пользователя страница 122

7-10

CHAPTER

7

Staple cartridge replacement

The message “

SLIDE THE FINISHER AWAY FROM THE COPIER

AND ADD STAPLES.

” will appear when the staple cartridge is empty.

Replace the staple cartridge as follows:

1

While holding the finisher release lever, slide the finisher
away from the copier.

2

Lower the lock lever to unlock the stapler unit.

3

Turn the stapler unit to face up.

4

Hold the staple box release lever to unlatch the staple
box.

5

Remove the staple box.

6

Remove the empty staple cartridge from inside the
staple box.

7

Insert the new staple cartridge into the box until it clicks
in place.

●

Insert the new cartridge by aligning the arrows on the cartridge
with those on the box. Check that the cartridge locks in place by
pulling it slightly.

●

The cartridge holds 5,000 staples.

OPTIONAL EQUIPMENT

Finisher (AR-FN3)

FINISHER (AR-FN3)

Содержание AR-505















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды