Sharp AR-405 Скачать руководство пользователя

Страница: 78 / 178

4-2

CHAPTER

PAPER

Types and sizes of copy paper

Size

Weight

Capacity

Special paper

(80

(21lb.)

paper)

Paper trays

A5 to A3

56 to 105

500 sheets

1 and 2

(5-1/2" x 8-1/2"

(15 lbs. to 28 lbs.)

to 11" x 17")

Bypass tray

A6 to A3

52 to 128

50 sheets

Transparency film, labels,

(5-1/2" x 8-1/2"

(14 lbs. to 34 lbs.)*

tracing paper, cover stock**

to 11" x 17")

(Ordinary paper)

(200

(110 lbs.)), index

stock** (176

(65 lbs.))

●

For best results, use only paper recommended by SHARP.

* For paper weighing from 105 to 128

(28 to 34 lbs.), A4 (8-1/2"

x 11") is the maximum size that can be fed through the bypass tray.

** Paper heavier than 128

(34 lbs.) must be fed narrow side into the

feed slot of the bypass tray.

Loading copy paper

“

OPEN TRAY AND ADD PAPER.

” will be displayed when there is

no copy paper in a selected paper feed station.
When a selected paper tray is not installed or is improperly installed,
“

PUSH PAPER TRAY INTO THE MACHINE UNTIL IT

LATCHES.

” will be displayed. Install it or push it back firmly into

place.
For best results, use only Sharp recommended paper.

SUPPLIES

Paper

Содержание AR-405



















































































































































































Результаты поиска

Содержание AR-405

Отзывы:

Похожие инструкции для AR-405

Бренды по названию

Популярные бренды

Sharp AR-405, Руководство по эксплуатации

Результаты поиска

Содержание AR-405

Отзывы:

Похожие инструкции для AR-405

Бренды по названию

Популярные бренды