Sharp AR-405 Скачать руководство пользователя

Страница: 40 / 178

3-6

CHAPTER

This copier has an edge erase mode and a centre erase mode.

●

Edge erase can be used to eliminate shadow lines around the edges of
copies caused when thick paper or a book is used as an original.

●

Centre erase can be used to eliminate the shadow produced by the
bindings of bound documents.

●

Edge + centre erase can be used to eliminate shadow lines around the
edges of copies and to eliminate the shadow at the centre of copies.

●

The standard erase width is 10 mm (1/2"), but can be changed from 0 mm
to 20 mm in 1 mm increments (from 0" to 1" in 1/8" increments).

★

KEY OPERATOR The initial setting of the width for edge erase and centre
erase can be changed. See page 8-16.

SPECIAL FUNCTIONS

Erase

ERASE

A B

Edge erase

Centre erase

Place the original in the document feeder tray or on the
document glass.

Press the SPECIAL MODES key.

●

The SPECIAL MODES screen will appear.

Press the “ERASE” key on the touch panel.

●

The setting screen for ERASE will appear.

READY TO COPY.

ERASE

EDGE ERASE

CENTRE ERASE

EDGE+CENTRE

ERASE

CANCEL

(0~20)
mm

READY TO CO

READY TO COPY.

SPECIAL MODES

MARGIN SHIFT

MULTI SHOT

PAMPHLET COPY

ERASE

COVERS

IMAGE EDIT

TEXT STAMP

TRANSPARENCY

INSERTS

DUAL PAGE

COPY

AUTO

EXPOSURE

PAPER SELECT

100%

COPY RATIO

AUTO A4

Edge + Centre erase

Содержание AR-405



















































































































































































Результаты поиска

Содержание AR-405

Отзывы:

Похожие инструкции для AR-405

Бренды по названию

Популярные бренды

Sharp AR-405, Руководство по эксплуатации

Результаты поиска

Содержание AR-405

Отзывы:

Похожие инструкции для AR-405

Бренды по названию

Популярные бренды