Sharp AR-162S Скачать руководство пользователя | Manualshive

Страница: 30 / 68

background image

28

ST
A

TUS

INDICA

T

ORS

1

Open the bypass tray. Lift slightly on the side cover and
slide the cover out until it stops.

2

Push gently on both sides of the front cover and open it.

3

Push the toner cartridge lock release lever and pull the
toner cartridge out. Remove the toner cartridge while
supporting it with the left hand at the green label position.

●

For disposal of the old toner cartridge, contact your dealer.

After removing the toner cartridge, do not shake it or tap
on it. Doing so may cause toner to leak from the
cartridge. Put the old cartridge immediately in the bag
contained in the box of the new cartridge.

4

Remove the new toner cartridge from the bag. Grasp the
cartridge on both sides and shake it horizontally four or
five times. After shaking the cartridge, remove the tape.

Grasp the grip when holding the cartridge. Do not hold
the cartridge by the shutter. Be sure to only shake the
cartridge before the tape is removed.

TONER CARTRIDGE REPLACEMENT

When the toner cartridge replacement required (

) indicator lights up,

replacement of the toner cartridge will be needed soon. Obtain a new
cartridge. When the toner cartridge replacement required (

) indicator

blinks, the toner cartridge must be replaced before copying can be resumed.
Replace the toner cartridge by following the procedure below.

For best copying results, be sure to use only
SHARP Genuine Supplies which are designed,
engineered and tested to maximize the life and
performance of SHARP copiers. Look for the
Genuine Supplies label on the toner package.

Toner cartridge replacement

Grip

Toner cartridge lock
release lever

4 or 5 times

Tape

Shutter

During a long copy run of a dark original, the
indicator may blink and the copier stop, even though
toner is left. The copier will feed toner up to 2 minutes
and then the START key indicator will light up. Press
the START key to restart copying.

«
...
28
29
30
31
32
...
»

Содержание AR-162S





































































Отзывы:

Нет отзывов

Похожие инструкции для AR-162S

Бренд: Xerox Страницы: 5

Бренд: Triumph Adler Страницы: 424

C11 - DocuPrint Color Inkjet Printer

Бренд: Xerox Страницы: 84

Бренд: Oce Страницы: 18

Бренд: Xerox Страницы: 402

Бренд: Panasonic Страницы: 12

Бренд: Olivetti Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды