Sharp AR-162S Скачать руководство пользователя | Manualshive

Страница: 29 / 68

background image

27

MAKING COPIES

Toner save mode

1

Press the AUTO/MANUAL/PHOTO key to select the
MANUAL mode.

2

Press and hold down the AUTO/MANUAL/PHOTO key
for approximately 5 seconds.

●

The MANUAL indicator will go out and the PHOTO indicator will
begin to blink.

●

The exposure indicator marked “5” will light up, indicating that the
standard toner mode is active.

3

To enter the toner save mode, press the light (

) key.

●

The exposure indicator marked “1” will light up, indicating that the
toner save mode is selected.

4

Press the AUTO/MANUAL/PHOTO key.

●

The PHOTO indicator will stop blinking and will light up steadily. The
toner save mode is now active.

●

To return to the standard mode, repeat the procedure but use the dark
(

) key to select exposure level “5” in step 3.

TONER SAVE MODE

This mode reduces toner consumption by approximately 10% in the automatic
and manual exposure modes. Copies will be lighter but still adequate for
general use. Selection of this mode does not affect the PHOTO mode. Follow
the procedure below for setting the toning level.

«
...
27
28
29
30
31
...
»

Содержание AR-162S





































































Отзывы:

Нет отзывов

Похожие инструкции для AR-162S

Бренд: Xerox Страницы: 4

Бренд: Canon Страницы: 524

Бренд: Epson Страницы: 53

Document Centre 240

Бренд: Xerox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды