9) Measure the distance H between the paper lead edge and the
image print start position. Set the image print start position set
value (Exposure display <EXP1> ON) again.
•
1 step of the set value corresponds to about 0.127mm shift.
•
Calculate the set value from the formula below.
99 - H/0.127 (mm) = Image print start position set value <H: Print
start position measurement value (mm)>
Example: 99 - 5/0.127 = 99 - 39.4 = about 59
Note: If the set value is not obtained from the above formula,
perform the fine adjustment.
10)Set the main cassette lead edge void adjustment value (Exposure
display <PHOTO> ON)* again.
•
1 step of the set value corresponds to about 0.127mm shift.
•
Calculate the set value from the formula below.
B/0.127 (mm) = Lead edge void adjustment value <B: Lead edge
void (mm)>
Example: When setting the lead edge void to 2.5mm:
2.5 /0.127 = about 20
Note: If the set value is not obtained from the above formula,
perform the fine adjustment.
*
2nd tray lead edge void adjustment: Exposure display <AUTO
+ PHOTO>
Multi bypass tray lead edge void adjustment: Exposure display
< PHOTO>
OC 2nd print surface (Auto duplex) lead edge position adjustment:
Density display <EXP3>
OC 2nd print surface (Auto duplex) lead edge void adjustment:
Exposure display <None>
*
For the adjustment procedure, set to S
→
D mode
Note: Before performing the 2nd print surface lead edge position
adjustment and the lead edge void adjustment, be sure to
perform the 1st print surface lead edge position adjustment
in advance, and be sure to perform the 2nd print surface
lead edge position adjustment and then the lead edge void
adjustment in this sequence.
<Adjustment specification>
Adjustment
mode
SIM
LED
Set value
Spec
value
Set
range
OC image
lead edge
position
SIM
50-1
AUTO
99
R/0.127
Lead
edge
void: 1 -
4mm
Image
loss: 3mm
or less
1
∼
99
Main
cassette lead
edge void
PHOTO
B/0.127
2nd tray lead
edge void
AUTO +
MANUAL
+ PHOTO
Multi bypass
tray lead
edge void
MANUAL
+ PHOTO
Print start
position
EXP1
99 –
H/0.127
OC 2nd print
surface lead
edge position
adjustment
SIM
50-1*
EXP 3
1 step:
0.127mm
shift
OC 2nd print
surface lead
edge void
adjustment
No display
1 step:
0.127mm
shift
*
(Set to S
→
D mode for before execution)
b. SPF image lead edge position adjustment
1) Set a scale on the OC table as shown below.
Note: Since the printed copy is used as a test chart, put the scale in
paralled with the edge lines.
2) Make a copy, Then use the copy output as an original to make an
SPF copy again.
3) Check the copy output. If necessary, perform the following adjust-
ment procedures.
4) Execute SIM 50-1.
5) Set the SPF lead edge position set value (Exposure display
<MANUAL> ON) so that the same image is obtained as that ob-
tained in the previous OC image lead edge position adjustment.
<Adjustment specification>
Adjustment
mode
SIM
LED
Set value
Spec value
Set
range
SPF image
lead edge
position
SIM
50-1
MANUAL
1 step:
0.127mm
shift
Lead edge
void: 1 -
4mm
Image loss:
3mm or less
1
∼
99
5
10
0mm
0mm
*
Fit the print edge with the paper edge, and perform the
lead edge adjustment.
5
10
2.5mm
2.5mm
AR-162 [6] ADJUSTMENT 11/1/2000
AR-162 ADJUSTMENTS – 3