Sharp AL-1600 страница 41 Скачать руководство пользователя | Manualshive

Страница: 41 / 47

background image

48

Section 6.

Physical Chemical Characteristics

Boiling / Melting Point: Not applicable

Specific Gravity:

1.1

Vapor Pressure:

Not applicable

Solubility in Water: Negligible

Vapor Density:

Not applicable

PH:

Not applicable

Evaporation Rate:

Not applicable

Viscosity:

Not applicable

Appearance:

Fine powder

Color:

Black

Odor:

Odorless

Section 7.

Fire and Explosion Data

Flash Point (Method Used):

Not applicable

Ignition Temperature:

>350

°

C

Flammable Limits:

(LEL); Not applicable

(UEL); Not applicable

Extinguishing Media:

CO

2

, dry chemical, foam or water

Special Fire Fighting Procedure:

None

Unusual Fire and Explosion Hazard: This material has no unusual fire or explosion hazards.
Sensitivity to Mechanical Impact:

None

Sensitivity to Static Charge:

None

Section 8.

Reactivity Data

Stability:

Stable

Incompatibility (Material to Avoid):

None

Hazardous Decomposition:

CO and NOx

Hazardous Polymerization:

Will not occur.

Section 9.

Precautions for Safe Handling and Use

Personal Protection Information (Respiratory, Eye Protection and Protective Glove):

Use of a dust mask is recommended when handling a large quantity of toner or during long
term exposure, as with any non-toxic dust.

Engineering Control / Ventilation:

Not required.

Work / Hygienic Practice:

Inhalation should be minimized as with any non-toxic dust.

Steps to be taken in case of Spill or Leak: Sweep up or clean up with vacuum cleaner.
Waste Disposal Method:

Waste material may be dumped or incinerated under conditions

which meet all federal, state and local environmental regulations.

Section 10. Regulatory Information

NFPA Rating (U.S.A.):

Health = 1

Flammability = 1

Reactivity = 0

WHMIS Legislation (Canada):

This product is not a controlled product.

Transport Information:

This product is not a hazardous material.

UN No.:

None allocated.

Section 11. Other Information

References: IARC (1996) IARC Monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans,

Vol. 65, Printing Process and Printing inks, Carbon Black and Some Nitro Compounds, Lyon, pp-
149-261
H. Muhle, B. Bellmann, O. Creutzenberg, C. Dasenbrock, H. Ernst, R. Kilpper, J. C. MacKenzie,
P. Morrow, U. Mohr, S. Takenaka, and R. Mermelstein (1991) Pulmonary Response to Toner upon
Chronic Inhalation Exposure in Rats. Fundamental and Applied Toxicology 17, pp. 280-299

«
...
39
40
41
42
43
...
»

Содержание AL-1600
















































Отзывы:

Нет отзывов

Похожие инструкции для AL-1600

Бренд: Olivetti Страницы: 332

Color imageRUNNER C3380 Series

Бренд: Canon Страницы: 550

Бренд: Panasonic Страницы: 130

Бренд: Xerox Страницы: 7

C123 Copycentre

Бренд: Xerox Страницы: 2

Бренд: Oki Страницы: 386

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды