Sharp AL-1600 Скачать руководство пользователя

Страница: 32 / 47

GENERAL INFORMA

TION

The TD cartridge is not installed. Install the
TD cartridge.

Side cover is open.
Close the front and side covers securely.

The TD cartridge must be replaced. See page
24, TD CARTRIDGE REPLACEMENT.

A misfeed has occurred. See page 28,
MISFEED REMOVAL.

Toner replenishment takes up to 2 minutes.
Wait until the START key (

) indicator

stops blinking.

Connect the copier to a power outlet which is
not used for other electric appliances.

●

blinking in the copy

quantity display?

●

steadily lit in the copy

quantity display?

●

Is the

indicator blinking?

●

Is the

indicator blinking?

●

Is the START key (

) indicator

blinking?

●

Is the same power outlet used for
the lighting fixture and the copier?

Self-diagnostic function

An automatic self-diagnostic function is built into the copier. Should the
copier malfunction, the self-diagnostic function will locate the problem and
stop the copier to prevent damage. An alphanumeric code will appear in the
copy quantity display.

Example

Should the copier completely stop and a letter and a number appear alternately,
contact your SHARP service center immediately.

Be sure to use only genuine SHARP parts and supplies.

Please contact your SHARP service center immediately if a problem persists
after checking the above.

Problem

Solution

●

Is the POWER SAVE (

)

indicator blinking?

●

Is the

indicator on?

Wait until warm-up is complete.
Warm-up time is approximately 35 seconds.

Copy paper is needed. See page 13, LOADING
COPY PAPER.

Power is on but copying
is not possible.

Copier trouble?

COPIER TROUBLE?

Lighting fixture flickers.

Содержание AL-1600
















































Результаты поиска

Содержание AL-1600

Отзывы:

Похожие инструкции для AL-1600

Бренды по названию

Популярные бренды

Sharp AL-1600, Руководство по эксплуатации

Результаты поиска

Содержание AL-1600

Отзывы:

Похожие инструкции для AL-1600

Бренды по названию

Популярные бренды